Consider a series RLC circuit with L - 0.5 H, C = 3.0 µF, R = 10.0 is connected to an AC voltage source V(t) = Vo sin(wt) which has a maximum voltage amplitude Vo = 10V. = Calculate the quality factor for this series RLC circuit. Now consider a parallel RLC circuit with the same parameters(R, L and C) and calculate the quality factor for the same. To make a high quality resonator, how do you expect the R should be changed(given L and C remain same) for series and parallel RLC circuit?

Consider a series RLC circuit with L - 0.5 H, C = 3.0 µF, R = 10.0 is connected to an AC voltage source V(t) = Vo sin(wt) which has a maximum voltage amplitude Vo = 10V. = Calculate the quality factor for this series RLC circuit. Now consider a parallel RLC circuit with the same parameters(R, L and C) and calculate the quality factor for the same. To make a high quality resonator, how do you expect the R should be changed(given L and C remain same) for series and parallel RLC circuit?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter23: Resistive-inductive-capacitive Series Circuits

Section: Chapter Questions

Problem 1PA: You are an electrician working in a plant. A series resonant circuit is to be used to produce a high...

See similar textbooks

Similar questions

The graph shows the current vs. frequency graph of FOUR (4) RLC series circuits with different combinations of resistance (R) and capacitance (C) values. The value of L and the peak-to-peak voltage across both sets of data are the same. Find the following quantities:
Design a 1st order Butterworth circuit with a band-pass with a cutoff frequency of 100 Hz to 100 kHz. Analyze AC / DC
A resistance of 100 and a capacitance of 100 µF is connected in series to the parallel combination of a 20-0 resistor and a 15-mH inductor. The circuit is energized by a 120 Vac, variable frequency supply. Derive the formula for resonant frequency and use it to find the resonant frequency.
3- Analyze the system shown below to find the output waveform, Vout, assume the capacitor voltage value is -1.0 V at t-0 and RC-1 msec. -0.5 -1.0 V(1), V 1.0 0.5 R $ AAA f, msec
Activity 5: Part A A resistive load RL is fed by a DC network as shown in the figure below. Determine the value of the resistance R so that the maximum power transferred to the load is 4 mW. R ww R ww IV RL 2V Part B The resonant circuit for a radio broadcast is shown below. It consists of a 160-pF capacitor in parallel with a 250 uH inductor with an internal resistance of 80 N. Determine the resonant frequency of the circuit (in kHz). Im cos(wt)
A 100 Hz sinusoid is sampled at thrice the nyquist rate. Then how many samples are obtained in 2sec.
4. Find Idc, Vdc and the capacitance that will force the Vr(pp) to 2mV. Draw the output waveform across the capacitor. Fin=60HZ. TX1 D1 Ge Vac Lst 230V Lp 1 RL 12-0-12 Center tapped CL 1k D2 Ge 2
1- Express the following RC circuit in state-space form. R ei eo i C ees
100 used to compand A companding system with u from 0V to 10 V sinusoid signal. Draw the characteristic of the typical system.
A coutimuous-time sinusoid has frequency 2 = 70r rads sec and is sampled at a sampling interval of T=0.01 sec. What is the frequency of the discrete-time sinusoid? %3D Oa =70z rads ses OL- 0.7z rada sec Oce= 7x rads sec Od0= 7000r ads see
Ex: Design a noninverting summer circuit to achieve a 3 summing function for two analog signals 3 filt) = 5 Sin 2πT 10³t and f(t) = Ult). Draw the output waveform.
A parallel R-L-C circuit is fed by a constant current source of variable frequency. The circuit resonates at 100 kHz and the Q-factor measured at this frequency is 5. Find the frequencies at which the amplitude of the voltage across the circuit falls to (a) 70.7% (b) 50% of the resonant frequency amplitude.