Consider a regenerative gas-turbine power plant with two stages of compression and two stages of expansion. The overall pressure ratio of the cycle is 9. Argon enters each stage of the compressor at 300 K and each stage of the turbine at 1200 K. Assuming constant specific heats, determine the minimum mass flow rate of argon needed to develop a net power output of 115 MW. The properties of argon at room temperature are cp = 0.5203 kJ/kg-K and k = 1.667. The minimum mass flow rate of argon is kg/s.

Consider a regenerative gas-turbine power plant with two stages of compression and two stages of expansion. The overall pressure ratio of the cycle is 9. Argon enters each stage of the compressor at 300 K and each stage of the turbine at 1200 K. Assuming constant specific heats, determine the minimum mass flow rate of argon needed to develop a net power output of 115 MW. The properties of argon at room temperature are cp = 0.5203 kJ/kg-K and k = 1.667. The minimum mass flow rate of argon is kg/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve 3.47 by hand
If a wooden block of weight W = 9.7 N placed on a smooth surface inclined at .2 %3D 大 an angle 35 and is at rest, then the reaction (F) offered by the surface is 35° - 5.6 N O ON
1-) Balancing masses from the axis of rotation to the distance of ei and Li mm in the rotor R and L balancing planes seen in the figurewant to balance by putting, Find the balancing masses and angular positions to be used in balancing. Tableuse the given values. Find L and R support reactions.
A board sits in equilibrium. On the left end, there is a wire that supports the board from the ceiling, and to the right, there is a sawhorse that supports the board from the ground. The sawhorse is a distance d= 1/5l from the right edge of the board. There is a block with mass ms= 4.5kg that is a distance 3/4l from the right edge of the board. Finally the board has a mass mb= 11kg. c) Write down Newton's 2nd law. Put the equation in terms of mb, ms, g, T, and Fn. Where T is the tension in the wire, and Fn is the normal force of the sawhorse on the board. d) Write down Newton's 2nd Law for rotations. Put the equation in terms of l, mb, ms, g, T, and Fn.
Q2/ Determine the moment of the force system as shown in fig.(2) about point (0) when ; a) The force (F) is vertical force and equal to (100ON) b) The force (F) is horizontal force and equal to (100N) F=100N F=100N 60° 60 Fig.(2)
Q5: For the puller shown in Fig.5, determine the horizontal and vertical components of the forces at A and B 2000N 720 ESSESE 20 2 Fig.5
Q4 / 1. For the force system shown in ( fig.4) below the resultant ; (R) is equal to ( 500N) , the angles( a ) and (ß) are ; (25°) and (55° ) respectively ; Determine the value of the component (P) R=500N a= 25° Fig. (4)
A balanced rigid disc mounted on a rigid rotor has four identical point masses, each of 10 grams, attached to four points on the 100 mm radius circle shown in the figure. r = 100 mm The rotor is driven by a motor at uniform angular speed of 10 rad/s. If one of the masses gets detached then the magnitude of the resultant unbalance force on the rotor is
From the following system, obtain the force components for the system X∗ and Y∗ in terms of i and j. It is known that for the system y and x the value of the force components is F = (F76 N i - F500 N j) N . Solve by any analytical method. (use the values on the image (pea1) not the values on image (pea2))
5. Calculate the components of resultant force of the three coplanar concurrent forces, as shown. 800 N y 75% X 30⁰ 1500 N 1000 N A) R =-537.28 N, R, = 809.31 N B) R = 537.28 N, R = -845.79 N C) R =-2060.8 N, R = -809.31 N D) R = 537.28 N, R = -809.31 N
Find the true magnitude and direction of the support forces A, B.