Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If σ = 11 MPa in the direction shown, determine the principal stresses at the point. 28.6 MPa and -33.6 MPa 20.7 MPa and -42.4 MPa 39.6 MPa and -46.7 MPa 26.8 MPa and -35.8 MPa 34.2 MPa and -40.0 MPa

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Eigure 6)…

A: So angle is clockwise and θ=-30°σx=31ksiσy=-38ksiτxy=0

Q: ) Write the equation for the neutral axis in the cross-section. b) Draw the normal stress…

A:

Q: rtical planes at the point are Sx= 22 ksi, S, = 6 ksi, and Sy 13 ksi %3D Draw Mohr's circle for this…

A: σx=22ksiσy=-6ksiτxy=-13ksiRadius of the…

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 95 MPa and Sy =…

A:

Q: determine the principal stresses at the point.

A: Principal stresses

Q: point, another plane B, inclined at 45°, on the normal aly Mohr's stress circle technique to find…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sy = 60 MPa and Sy =…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S, = 75 MPa and 5, =…

A: Given data in question  Stresses Angle To find out Normal and shear stress

Q: The state of stress at a point is the result of two loadings as shown in figure. When acting alone,…

A: For the two loadings act simultaneouslythen resultant (absolute) shear stress at that point with…

Q: The stresses shown act at a point in a stressed body.  The stress magnitudes are Sx = 75 MPa and Sy…

A: Given data in question  Normal stresses Angle To find out  Normal and shear stresses

Q: The stresses shown act at a point in a stressed body. Determine the normal and shear stresses at…

A:

Q: The stresses shown act at a point on the free surface of a machine component. Normal and shear…

A: The given data is shown below: Sx=12.4 ksiSy=3.5 ksiSxy=3.6 ksiβ=29°

Q: The stresses shown act at a point on the free surface of a machine component. Normal and shear…

A: Using transformation equation

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: ee surface of a machine component. Normal and shear stress magnitudes acting on horizontal and…

A: Radius of the circleR=(sx-sy2)2+sxy2R=(23.6-2.82)2+72R=12.54 ksisAVG=sx+sy2=23.6+2.82sAVG=13.2ksi

Q: The stresses shown in the figure act at a point in a stressed body. The stress magnitudes are Sx =…

A: Given: The stress in the x-direction (Sx) is 170 MPa. The stress in the y-direction (Sy) is 85 MPa.…

Q: 6) Across Plane #1, the state of stress is measured as: On 1.1 kb and os= 0.4 kb Across Plane #2…

A:

Q: In the figure below is a slim, high-strength steel rule (E = 30X106 psi) having thickness 0.175 in.…

A: A) Given data ; E = 30 X 106 psi Thickness = 0.175 inches Length is = 48 inches To Find : Determine…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A: Calculate principal stresses at point

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: For the state of plane stress shown below. 74. Determine the largest value of σy for which the…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are Sx - 60 MPa and Sy=…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A:

Q: The stresses shown in the figure act at a point on the free surface of a machine component. If o =…

A:

Q: Q.6 A beam has solid circular cross-section having diameter d. If a section of the beam is subjected…

A:

Q: Which of the following most nearly gives the elastic deformation in the bronze rod?  a. 0.58 mm b.…

A:

Q: The differential element above represents the state of plane stress at a pont J steel beam. Which of…

A: Given data: σX=60 ksiσY=-20 ksiζXY=40 ksi

Q: For the state of stress given in the illustration below, determine the normal and shear stresses on…

A: Given, Horizontal stress (compressive), σx = 7250 psi  Vertical stress (tensile), σy = -29000 psi…

Q: For the stressed elements allocated to you, find the values and sketch the orientations: a) Maximum…

A: Given data, Compressive stress along the y-axis, σy = -80 MPa Tensile stress along x-axis, σx= 40…

Q: As shown in the figure below the two planes PQ and QR are having shear stress of 40 MPa. The plane…

A:

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

A:

Q: mine the maximum shear stress for the 7.. 3₁ == 0 MPa Txy=-31 Ox=37

A:

Q: The following stress element represents the stress state at point A of the structure in the figure…

A:

Q: ress at point A is ress at point Bis [ ksi. ksi.

A:

Q: If a point is subjected to the state shown in fig. , determine the principle stresses and the…

A:

Q: The stresses shown act at a point in a stressed body. The stress magnitudes are S,, - 95 MPa and S,…

A:

Q: 1. The member is loaded as shown. The diameter of the member is 32 mm. 1) Calculate all internal…

A:

Q: The following stress element represents the stress state at point A of the structure in the figure…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.