5 Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and verticalplanes at the point are shown. If 0 = 29 MPa in the direction shown, determine the principal stresses at the point.28 MPa16 MPa31.4 MPa and -38.0 MPa38.5 MPa and -31.0 MPa26.6 MPa and -18.5 MPa42.4 MPa and -29.4 MPa50.5 MPa and -34.6 MPa

The principal stresses. Given: The stress in the x-direction is σx=-16 MPa. The stress in the…

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If a = 29 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa 31.4 MPa and -38.0 MPa 38.5 MPa and -31.0 MPa 26.6 MPa and -18.5 MPa 42.4 MPa and -29.4 MPa 50.5 MPa and -34.6 MPa

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If a = 29 MPa in the direction shown, determine the principal stresses at the point. 28 MPa 16 MPa 31.4 MPa and -38.0 MPa 38.5 MPa and -31.0 MPa 26.6 MPa and -18.5 MPa 42.4 MPa and -29.4 MPa 50.5 MPa and -34.6 MPa

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.21P: An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec...

See similar textbooks

Similar questions

An clement m plane stress from the frame of a racing car is oriented at a known angle 8 (sec figure). On this inclined clement, the normal and shear stresses have the magnitudes and directions shown in the figure. Determine the normal and shear stresses acting on an clement whose sides are parallel to the \y axes, that is, determine crv, tr(_, and t, Show the results on a sketch of an clement oriented at B .
Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with respect to the element shown. Sketch the results on the element. 100 MPa 150 MPa T Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal stress at the point. Specify the orientation of the element in each case. 200 MPa 100 MPa 75 MPa 300 MPa
The state of plane stress at a point is represented on the element shown in the figure below. (a) Determine the principal stresses acting on this point, and the corresponding orientation (angle). (b) Determine the maximum in-plane shear stress, and the corresponding orientation (angle). Also determine the associated average normal stress. Draw Mohr's circle and show the stresses on the circle. 15 ksi 23 ksi 14 ksi
Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal stress. Specify the orientation of the element in each case
The stresses shown below act on horizontal and vertical planes through a point on the surface of a stressed body. Determine and show on a sketch the principal stresses and the maximum shear stress at this point. 30 ksi 5 ksi -20 ksi
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12 ksi, Sy = 17 ksi, and Sxy = 18 ksi.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses (σp1>σp2σp1>σp2) and the maximum in-plane shear stress τmaxτmax acting at the point.(c) Find the smallest rotation angle θpθp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
The stresses shown below act on horizontal and vertical planes through a point on the surface of a stressed body. Determine and show on a sketch the principal stresses and the maximum shear stress at this point. 50 MPa -30 MPa 35 MPa
Determine (a) the principal stresses and (b) the maximum shear stress and associated normal stress at the point in Figure 4. Specify and sketch the orientation of the element in each case. The directions of the stress components are as indicated in Figure 4. 100 MPa 200 MPa 300 MPa
A steel pipe (E1=200 GPa) surrounds a solid aluminum-alloy rod (E2 =70 GPa), and together they are subjected to a compressive force of 200 kN acting on rigid end caps. Determine the shortening of this metallic compression member, and determine the normal stresses in the pipe and in the rod.
For the plane-stress condition given below: σx = 400 MPa σy = 500 MPa τxy = - 30 MPa Construct a Mohr’s circle of stress, find: (a) the principal stresses and the orientation of the principal axes relative to the x,y axes (b) determine the stresses on an element, rotated in the x-y plane 60° counter?clockwise from its original position ; Show these stresses on a sketch of an element oriented at this angle (c) Also, using the matrix transformation law to compare the solutions with Mohr’s circle
At a certain point in a stressed body, the principal stresses are fx=80 MPa and fy=-40MPa. Determine the normal and shearing stresses on the plane whose normal is at +30 degrees with the X-axis.
At a point on the surface of a pressurized cylinder, the material element is subjected to stresses; σx = 60 MPa, σy = - 40 MPa, and τxy = - 30 MPa. Construct Mohr’s circle, then use it to determine the following: Do not use the equations of transformations.1- The principal stresses and the maximum shear stress.2- Show these stresses on sketches of properly stress elements.3- A point on the circle where the element is only subjected to pure shear stress. Calculate the value of that pure shear stress.