Consider a causal second-order system with the transfer function G(s) = lim c(t), rounded off your final answer to two decimal places. t → ∞ 1 1+2s + s² 1 with a unit - step R(s) = as an input. Let C(s) be the corresponding output. You have to find out the time taken by the system output c(t) to reach 94% of its steady-state value S

Consider a causal second-order system with the transfer function G(s) = lim c(t), rounded off your final answer to two decimal places. t → ∞ 1 1+2s + s² 1 with a unit - step R(s) = as an input. Let C(s) be the corresponding output. You have to find out the time taken by the system output c(t) to reach 94% of its steady-state value S

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

x(t) 3 2 1 Figure 1(a) 2 t
1. For the following system, use root locus techniques to design a compensator to satisfy the following criteria: a. -0.8, b. Zero steady-state error to step input. K(s + 2)(s + 1) (s – 2)(s – 1) R(s) + C(s)
O Exercise. In this exercise, you will examine the changes to the analytic step response of a transfer function with a single zero. Consider the transfer function used in the previous activity: 12+2 (a) Compute the symbolic form of the step response of the transfer function, x(1). You can perform the analytic computations by hand or using the Symbolic Math Toolbox. X Use these synbolic variables syns s z_e t positive X Write your solution here x = NaN (b) Plot the analytic step response with zo =-1 on the interval E (0, 10]. If you computed the step response function with the Symbolic Math Toolbox, you can use the matlabFunction command to convert it to a function handle that you can evaluate. X Create your plot here (c) Using the analytic form of the transfer function, compute the limit of the function as t+ 0o. X Write your solution here tlim = NaN
b) The unit step response of a first order system is shown below: Develop the transfer function of this system. Please include detailed steps. Hint: Please find the time constant and the constant gain (the numerator).
Consider the electrical circuit shown below. Obtain the transfer function Eo(s)/ E:(s) by using the block diagram approach then display the output response to the unit step input (u(t) = 1 t>0). Given that: %3D C = 5, C2 = 4C1, R1 10, and R2 = 3R1. %3D E(s) EAs) Cis C,s R2C28 + 1 Cs RI RI C25
bläi 3 A second order system that has the following properties Damping ratio of 0.75, underdamped natural frequency 10 rad/sec, and steady state value at zero is 1. Then the transfer function is 100 s2 + 10.75 s + 100 Option 4 O
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
Introduction to Control... Unit step response of system is 1 C(t) = (-et+e-²) for t > 0. The transfer function of system is. 8
Q3. Consider a system with the mathematical model given by the following differential equation. Find the transfer function of the system. 5 dy3 dt? dy + 5 dte dy dt
L Exercise. You can write the DC motor angular velocity transfer function as s + bs +c (a) Suppose that a DC motor has constants g = 60, b = 2.3, and e = 11. Define the transfer function in MATLAB using the tf function. % write your code here (b) Is the system stable? You can plot the poles in the s-plane using the pzmap function. For example, to plot the poles of a transfer function G, use: pznap(G) % write your code here (c) What are the poles of the transfer function? You can use the pole function to compute the poles of a dynamic system in MATLAB. For example, to identify the poles of a transfer function R, use: pole(R) % write your code here
You want a solution quickly, I don't have enough time
I don’t have more time pls reply