Consider a cart weighing 4,905 N, is moving to the left due to the application of force P = 100 N to its handle. Its mass center is located at G. Neglecting the mass and rolling resistance of the wheels, calculate the acceleration of the cart, resultant normal reaction at the front wheels and resultant normal reaction at the rear wheels.

Consider a cart weighing 4,905 N, is moving to the left due to the application of force P = 100 N to its handle. Its mass center is located at G. Neglecting the mass and rolling resistance of the wheels, calculate the acceleration of the cart, resultant normal reaction at the front wheels and resultant normal reaction at the rear wheels.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Statics, Civil Engineering The boat is pulling three water skiers. Skier A makes an angle of 30° with the boat driving direction, skier B makes an angle of 5°, skier C makes a negative angle of 15°. Suppose the magnitude of a force which impact on every skieracting on it is 900 N. Calculate The magnitude of the combined force and the angle which according to the direction of the boat journey.
A horizontal force F = 4s3 [N] is exerted on a 6-kg crate, where s is distance in meters. Assuming there is no friction, find the velocity of the crate when it has moved a distance of s = 4 m. 6 kg F E
pls answer completely
c) Consider the following expression of the force pushing a car of speed off the curve. P = gr Hence for constant velocity and so since P ox 1 Assume g = 10m/s mass= 1300kg r= 600m what is the centrifugal force P in terms of V?
Two blocks which are connected by a string, slides down an inclined plane. The coefficient of friction of block A is greater than the coefficient of friction of block B. Determine the acceleration of block B. ua 0.35 and ub e.25. B. 4 kg A 8 kg 30°
The box in the figure is 300kg. The box is pulled by the truck out of a ditch with a cable as shown in the figure. A constant force 2500 N is applied by the cable. The coefficient of kinetic friction between the box and the ground is 0.45. Please calculate the time for the box to reach a speed of 0.5m/s. 20
If the solid object shown is in equilibrium, the condition of equilibrium is expressed mathmatically as FR = F1 + F2 + F3 = 0, where FR is the resultant force. and (MR)o = M1 + M2 = 0, where is the resultant moment about point O.
An rectangular tank 180 cm wide, 200 cm long has a height of 80 cm. It contains solution of specific gravity 1.20 to a height of 50 cm. The above tank is horizontally accelerated to the right along its width at a rate of 6 m/s². At the given acceleration, determine the following: force on the inside left panel of the tank in kg. (b) force acting at the bottom of the tank in kN.
E2
Example 2 A steel shaft with 800 N.m constant diameter of 50 mm is loaded 1300 N.m as shown in the figure by torques 1200 N.m D applied to gears fastened to it. Using 2 m 700 N.m C 1.5 m G= 83 GPa, compute in degrees the 3 m relative angle of rotation between OBA SIT gears A and D.
Situation 1: Two blocks J and K are connected by a strut. The coefficients of static and kinetic friction between surfaces are 0.35 and 0.21, respectively. 35 =0 A. If block K weighs 90 kN. what is the required weight of block J for motion to impend? At the same instance, what is the force in the strut? B. If block J weighs 80 kN. what is the required weight of block K to prevent motion? At the same instance, what is the force in the strut? C. If blocks J and K weighs 50 kN and 70 kN, respectively, what is the required leftward force P to be applied at block K to just start the motion? At the same instance, what is the force in the strut? D. If blocks J and K weighs 100 kN and 10 kN, respectively, what is the required leftward force P to be applied at block K to just prevent motion? At the same instance, what is the force in the strut?
The particle of mass m = 2.0 kg is attached to the light rigid rod of length L = 1.17 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity θ˙ = ω = 2.0 rad/s. Determine the force T in the rod when θ = 20°. The force T is positive if in tension, negative if in compression.