Consider a bar having the following properties, a = 6.6x10-06/°F, E = 29×10% psi, having a diameter of 0.25 in and length 2 ft is fixed from one end and other end is attached to a spring as shown below: m The spring constant is k=1000 lb/in, the temperature is raised by 40°F. Find the force developed in the bar. a) 6.23 lb b) 10.29 lb c) 0 lb d) 2.33 lb

Consider a bar having the following properties, a = 6.6x10-06/°F, E = 29×10% psi, having a diameter of 0.25 in and length 2 ft is fixed from one end and other end is attached to a spring as shown below: m The spring constant is k=1000 lb/in, the temperature is raised by 40°F. Find the force developed in the bar. a) 6.23 lb b) 10.29 lb c) 0 lb d) 2.33 lb

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Ax = 0.45 kN and Ay = 0.32 kN Ax = 0.1 kN and Ay = 0.23 kN Q) Consider a weight supported by a cable as shown in figure below is equal 100 kN. Determine the force in * cable AB A B 40° W F = 5016 kN O F = 5014 kN F = 5010 kN F = 5012 kN Q) Four forces act on an eye bolt as
令ll 31 ZAIN IQ zain 1Q Q1: MO =S 400 lb F1 = 400 j F2 = -600 k F3 = 500 sin 45 i -500 cos 45 k 3 r2=? 600 lb r3=? 45° M- 11XF,, M,= r2* F, M,= r3x F, M-M, + M, + M, 500 lb *:س 2 1.5m P= 0.8 kN T-12 kN 3m Determine the x-, y-, and z- components of T. Determine the angles which the line of action of T forms with the positive x-, y-, and z-axes. Calculate the projection of P onto a line between A and F and determine the angle between P and AF. Determine the vector expression for the moment of P about point E. اضف ملف ک
It is located on the ground with a safety stress of 50 kg/cm^2. a) Find the biggest P value that can be transported depending on the ground. b) Determine the fundamental thickness depending on this load. (Slip safety stress for foundation and material= 100 kg/cm^2)
A cylindrical rod of diameter 23 mm and length 234 mm is subjected to a tensile load of 57 kN and it elongates to 0.5 mm. Find Young's Modulus (Modulus of Elasticity). Solution: i) Cross-section Area, A = ii) Stress = iii) Strain = iv) Young's Modulus =
I need answer within 20 minutes please please with my best wishes
4.) Please help with equation, gravity is g=32.2 ft/sec^2 or g=9.81 m/sec^2
A 200 kN В 30 kN D Soil Surface 1 mm settlement An axially loaded column made up of different segments AB, BC, and CD has a fixed support at A and a footing at D. The footing at D is rigid but is supported by soil that settles (moves downward) a maximum of 1mm before offering any resistance. Determine the stresses in segments AB, BC, and CD. Note, neglect the weights of the members.
A uniform drawbridge must be held at a 38.5 ∘ angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 13.0 m long, and pivots about a hinge at its lower end. A cable is connected 3.80 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. a) What is the tension in the cable? b) Find the magnitude of the force the hinge exerts on the bridge. Find the direction of the force the hinge exerts on the bridge. c) If the cable suddenly breaks, what is the initial angular acceleration of the bridge?