Concept of remote damage
Q: Explain any three types of excavation
A: Excavation is the process of excavating and removing volumes of earth or other materials for the…
Q: Define the term capillary fringe.
A: The capillary fringe is characterized as the saturated zone of water immediately just above the…
Q: Define direct shear test ?
A: Direct shear test: It is a laboratory or field test used to measure the shear strength of the soil.…
Q: What is susbtainable design?
A: Answer Introduction Sustainable design is defined as these are those that seek to minimize the…
Q: The weight of a car, moving at a constant speed on a beam bridge, is modeled as a single…
A: Question is based on a car moving at constant speed at beam bridge . Magnitude of load and length of…
Q: 1. A square piece of land 60m x 60m is to be leveled down to a level coinciding to elevation zero.…
A: Excavation depth = average elevation - zero Determine Volume of cut, V = grid area * average…
Q: of nsions? O Option 1
A: Option 1,2, 3 does not completely give the dimensions of their respective figures.
Q: 10 ft 5 ft 1 Az 3 ft Z Ay A 2 ft 8 ft 12 k D B₂ 6 k B Cy C₂/C By Bx Cx 7 ft / 4 ft --- X
A: This truss which we are solving is a space Truss. A space truss is used in the three-dimensional…
Q: What is shear starin rate?
A: Shear rate:
Q: Describe about the “nondestructive” type of testing?
A: The nondestructive test is used to evaluate the mechanical and physical properties of a material…
Q: What is base flow separation?
A: It is required to answer about what is base flow separation?
Q: Using unit load method, find the rotation at point (D) of the frame (ABCD) EI = 1.2 + 10* kN m2 40…
A: Calculating the force at A and C: RC*7=40*3(7+3/2) RC=1020/7 KN RA+RC=40*3 RA=-180/7 KN
Q: 3. A reservoir of water is connected to a 12-inch-diameter pipe that is 50 feet long and capped at…
A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…
Q: Draw the shear and bending-moment diagrams for the beam and loading shown, and calculate the maximum…
A:
Q: What is ASD method
A: Allowable Stress Design (ASD) It is also known as the service load design or working stress design…
Q: Describe the TRD method.
A: TRD stands for Trench Re-mixing and Deep wall. It is a one-phase process for excavation and in situ…
Q: Example 5.39 The thickened sludge from previous example 5.71 is to be digested anaerobically in a…
A: Given data- Note- Let the raw sludge loading rate- V1=100 m3/d, And, Total mass of solids = 1000…
Q: SIT 12. For the given figure below. El=constant 20 KN A 21 2m 2 m BI 4.5 m 25 KN/m Į Į 77 CI a.…
A:
Q: Explain the importance of Cone Penetration Test (CPT) ?
A: For estimating the basic fundamental soil mechanics properties of softer, sensitive soils, CPT (…
Q: What is Uniformly loaded strip ?
A: Answer:- Uniformly loaded strip: A uniformly loaded strip is defined as that strip which is…
Q: Where does The SPT-T procedure can be used?
A: This test incorporates the advantages of the Standard Penetration Test (SPT) and the Vane Shear Test…
Q: 131.6 kPa 53.6 kPa 315.2 kPa 315.2 kPa 35° 131.6 kPa 2. Find Normal and Shear Stress at Failure Plan…
A:
Q: The total degree of static indeterminacy of truss shown below is
A: Given truss-To Find-The total degree of static indeterminacy of the truss.
Q: For a given circular shaft of diameter 'D' having length T subjected to a torque T. If a concentric…
A: A solid shaft Diameter = DLength = L Shear stress = τ Hollow shaft External diameter = D Internal…
Q: Give an example of Variable-Inspection?
A: The evaluation of sampled articles on the basis of quantitative criteria under the quality control…
Q: What are the specifications of Lovar tape?
A: Lovar tape: It is also know as surveyors tape in which it is made up of the alloy. It is not an…
Q: Determine the forces in the x and y direction and the moment that must be applied at section 1 of…
A: The force acting on the pipe and nozzle assembly are a result of: Change in momentum of the flowing…
Q: Where the Schmertmann procedure applies?
A: Schmetmann method is used for the cohesionless soil for the calculation of bearing capacity of soil…
Q: Given below is the technical description of lot 2081, Cebu Cadastre. LINES 1-2 2-3 3-4 4-1 BEARINGS…
A: A technical survey description of lot 2081 is givenLinesBearingsDistance…
Q: A dry sand specimen is put through a tri-axial test. The cell pressure is 50 kPa and the deviator…
A: Given- Tri-axial testcell pressure σ3=50 kPadeviator stress σd=100 kPaAngle of internal friction ϕ…
Q: what is the impact of nonrecurring items?
A: Non-recurring items - An abnormal or rare gain or loss in the company's financial statement is…
Step by step
Solved in 2 steps