A computer room located on the second floor of a five-storey office building is 10 m x 7 m. The exteriorwall is 3.5 m high and 10 m long; it is a metal curtain wall (steel backed with 10 mm of insulatingboard), 75 mm of glass fiber insulation, and 16 mm of gypsum board. A double-glazed window makeup 30% of the exterior wall. The indoor temperature is 20 Celsius. calculate the cooling load at 8pmwith calculation safety factor of 1.25.Details about appliances and lightings:Computer: 200 watts, 5numbers, operating 8hrs every dayLights: 8 numbers fluorescent light, 30 watts each, assume opened from 4pm to 8am every-day.

-Cooling Load Calculation for cold rooms. during this article we’ll be watching the way to calculate…

computer room located on the second floor of a five-storey office building is 10 m x 7 m. The exterior all is 3.5 m high and 10 m long; it is a metal curtain wall (steel backed with 10 mm of insulating oard), 75 mm of glass fiber insulation, and 16 mm of gypsum board. A double-glazed window make p 30% of the exterior wall. The indoor temperature is 20 Celsius. calculate the cooling load at 8pm ith calculation safety factor of 1.25. etails about appliances and lightings: Computer: 200 watts, 5numbers, operating 8hrs every day

computer room located on the second floor of a five-storey office building is 10 m x 7 m. The exterior all is 3.5 m high and 10 m long; it is a metal curtain wall (steel backed with 10 mm of insulating oard), 75 mm of glass fiber insulation, and 16 mm of gypsum board. A double-glazed window make p 30% of the exterior wall. The indoor temperature is 20 Celsius. calculate the cooling load at 8pm ith calculation safety factor of 1.25. etails about appliances and lightings: Computer: 200 watts, 5numbers, operating 8hrs every day

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1P: Given the complex numbers A1=630 and A2=4+j5, (a) convert A1 to rectangular form: (b) convert A2 to...

See similar textbooks

Similar questions

At what height are the telephone outlets in this residence mounted? Give measurement to center. _____
Given the complex numbers A1=630 and A2=4+j5, (a) convert A1 to rectangular form: (b) convert A2 to polar and exponential form: (c) calculate A3=(A1+A2), giving your answer in polar form: (d) calculate A4=A1A2, giving your answer in rectangular form: (e) calculate A5=A1/(A2*) giving your answer in exponential form.
The concentration ratio of parabolic trough power plant is typically O a. from 30 to 40 O b. more than 1500 O c. less than 10 O d. from 10 to 20
8.1 The load duration curve for a power station is as shown in the below figure. The reserve capacity in the plant at 70% capacity factor is MW 90 50 % Time 100 (a) zero (b) 10 MW (c) 30 MW (d) 50 MW
Two 240V fluorescent lighting units are arranged to minimize the stroboscopic effect. The active and reactive current components of the unit 1 are 0.6A and 0.2A respectively. The active and reactive current components of the unit 2 are 0.3A and 0.6A respectively. Determine the value of total current consumed by the two units. A-Final active current component is B-Final reactive current component is C-Total current consumed by the two units are
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
The below table shows all the combinations considered when solving a unit commitment problem involving 3 thermal units, along with each unit's cost (in $/h) obtained when solving the economic dispatch for each combination. Unit 1 Off Off Off Off On On On On Unit 2 Off Off On On Off Off On On Unit 3 Off On Off On Off On Off On F₁ ($/h) F₂ ($/h) F3 ($/h) infeasible infeasible infeasible infeasible infeasible infeasible infeasible infeasible infeasible 1,753 0 3,855 5,484 0 0 5,006 0 681 3,125 2,535 0 2,882 2,339 681 Which one of the below combinations is the solution of the unit commitment problem? Select one: O a. None of these O b. Unit 1: ON, Unit 2: OFF, Unit 3: ON O c. Unit 1: ON, Unit 2: ON, Unit 3: OFF d. Unit 1: ON, Unit 2: OFF, Unit 3: OFF
For the first question, is the statement true or false: "The load is not absorbing nor generating reactive power"For the second question, is the statement true or false: "The load is absorbing 8.93kVA"
Calculate for: rise time, delay time, peak time, settling time, and percent peak overshoot
Draw the circuit diagram of Two quadrant chopper which is having average load voltage might be positive or negative. Explain each quadrant operation with neat sketch. I want more than 350 words and I do not want it in handwriting
Electronic ballasts and PCs are the most significant sources of triplen harmonics True False
There are 144 fuel cells are joined in a series through interconnects.there will be 4 stacks having 36 cell in each stack.these stacks are then oragnised in series and parallel combination to form a single module to deliver required voltage and output power.this SOFCs module then combined with CHP system to get thermal . From this data answer the following questions. a)Calculate voltage losses of module?.this question is very compulsory. b)Electrical efficiency of module? C)Thermal efficiency when module combine with CHP system? D)Combined electrical and thermal efficiency? The input parameters of single cell are given below: Ocv=1.020 Current density=2250mA/cm2 Power density=850mw/cm2 Cell active area= 121cm2 Net power=15kw System fuel utilization=80% Operating temp=550°c Cell voltage=0.8v Power of single cell=103 watt.