Compute the magnetic bearings of sides AB,BC, CD, DE AND AE.

Q: Q1-calculate the stress in the wire and the vertical deflection of point B using the given…

A: A beam is given, we need to find out the stress in the wire and vertical deflection of point B

Q: Calculate the forces on each member, assume each triangle is 45/45/90, B is a pin, M is a roller.…

A:

Q: 1. Using the method of joints, determine the force in each member of the trusses shown. State…

A: To find force in all the members of the truss

Q: وس 30 -8m 12m K 8KN 12m

A:

Q: 1. From the given figure shown below, determine the centroidal moment of Inertia (Ixo and lyo) of…

A: A built-up section is given The angles used = 53 in The steel plate used = 20 inThe channel section…

Q: Define the distance between the adjacent faces of the stock rail and the check rail , is called

A: The stock rail in the railway track are the main rails which are fixed. In the turnout the stock…

Q: Draw the shear diagram for the compound beam which is pin connected at B. Click on "add vertical…

A: Given : Draw the shear diagram of given figure below :

Q: 6200 N 4.5 m B O 2 m 1.5 m to 4.5 m & E b.) Determine the forces in members AB, BD and DE by the…

A: The given figure is shown below:

Q: Problem 12-Method of Sections 2m 2m 10 11 12 13 10

A:

Q: analysis of truss ( method of sections ) -Find Members BD, CD and CE

A: Given data  Using method of section find force in member BD, CD and CE.

Q: f the block is loaded with P = 287 kN, calculate the required dimension "b" of the key.

A:

Q: Resolve each force acting on the gusset plate intoits x and y components, and express each force as…

A: Consider F1

Q: Which joint would be the best place to start your analysis of the truss shown?

A:

Q: 5' Bk G E F

A:

Q: Instruction: Follow Given-Required-Solution format for your computation. Complete FBD for full…

A: To find clamping force at A

Q: DETERMINE THE FORCE IN EACH MEMBER BY THE METHOD OF JOINTS. F B 40 KN 4 at 3m - 12m OF TRUSS SHOWN…

A: Given data  Find force in each member using method of joint

Q: Determine the bolt diameter if the shear stress is 150 MPa and the bearing stress is 337.50 MPa.

A: The values and diagram given in the question are as follows: Shear stress(t)=150 MPa Bearing…

Q: #1. DETERMINE THE OF THE TRUSS UCE HORIZONTAL BY 10,000 kri A = Gin ² L₁ = 4FT L₂= JFT L3 = 12 FT P…

A:

Q: 8.66 9 B

A: GIVEN DATA:-⇒Length of the gate = 9 m⇒ρ = density= 1000 kg/m3→Gate dimensions:-⇒Width = 9m⇒Height =…

Q: Determine the member of forces of the truss. Utilize Method of joints and Method of section Put if…

A: To find force in all members of the truss

Q: write the equation for shear that you need to estimate the shear's magnitude at D. Estimate the…

A:

Q: If the resaltant force acting on the beracket is to be 750 N directed along the positive a asis,…

A: Given Force 1 = 325 N with slope 12/5 Force 2 = 600 N with angle 45° and resultant along x axis =…

Q: A wide flange and a channel have the following properties. They are attached as shown. -Wide Flange-…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: Determine the location (,) of the centroid of the wire AB, as shown in the following figure.

A: ##Determination of location of Centroid of Wire AB as shown in figure ###

Q: find: Cx & Cy

A: ∑MA=0-860 - 430×2 + Cx×2=0Cx=860 N →

Q: B 5/63 Determine the tensions in Ans. TAB 47.8 lb, TAC C 3 1 I 3-

A:

Q: Draw a shear diagram

A:

Q: M N 7.5 k 16 ft 15 k - J K 16 ft 15 k F G H 16 ft E A D E30 ft +20 ft --30 ft

A:

Q: In the plane truss system, the loading status of which is evident in the figure, the support…

A: Solution: Analysis of truss can be done by method of joint or method of section. The forces acting…

Q: Problem 7: Locate the centroid y of the cross-sectional area of the beam constructed from a channel…

A:

Q: A с k -8 m B D Not a joint 225 kN 8 m E 75 kN

A:

Q: F2-28. Determine the component of projection of the force along the line OA. F = 650 N 8 13. 12 5 A…

A: Given :

Q: C- Use the method of joints to determine the force in member CD d- Use the method of sections to…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: Using the method of joints, determine the force in each member of the truss. Summarize the results…

A: Let ,Length of AE, ED and BC be L.As the given triangle is equilateral, Perpendicular line drawn…

Q: 350N 200N 30 in

A: take summation of forces for resultant and use moment equilibrium for location

Q: Q2 All members of the truss in Figure Q2 are to be fabricated from the same stock of thin-walled,…

A:

Q: Make a cut through JK, CJ, and CD. The free-body diagram of the section to the right of the cut is…

A: Given data in question  Point loads Span member dimensions  To find out  Angle

Q: DRAW THE FBD AND JOINTS OF ALL. PROVIDE CLEAR SOLUTION. DO NOT COPY SOMEONE'S ANSWER

A:

Q: Figure Q3 shows the copper shaft subjected to the axial loads. Determine the displacement of end A…

A: