Answered: Compute the effective net area of the…

Engineering

Civil Engineering

Compute the effective net area of the built-up section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: snip

A: Calculate the gross area due to yielding. Ag=bt =5×12 =2.5 in2 Calculate the nominal…

Q: *A bracket is held in place using a circular pattern of 6 bolts as shown. The circular pattern…

Q: The vertical steel bar is connected with two A307 bolts (diameter = 7/8 inch) in standard round…

A: The values given in the question are as follows: Diameter of bolt(d)=7/8 in or 0.875 in bolt grade…

Q: The tension member shown contains holes for M20 bolts. At what spacing (mm), s, will the net area…

Q: 4. Determine the minimum net area of the angle section having a bolt hole with a clearance of 4mm.…

Q: Determine the net tensile area for the connection plate shown. Use a 3/8" plate with 3/4" bolts with…

A: Given data, Plate thickness (t)= (3/8) = inches Bolt dia = (3/4) inches So, hole diameter= dh =…

Q: Example 3.9 FIGURE 3.20 Find the available strength of the S-shape shown in Figure 3.20. The holes…

A: Given member: S15×50 Properties of the given section: Flange thickness=0.622 in We need to…

Q: The tension member shown in the figure contains holes for 3/4-in Ø bolts. At what spacing, s, will…

Q: 18" KA 1¼" O (3)-1" bolts Xplate

Q: The Plate shown in the fIgure has thickness of 12 mm. Diameter od bolts is 16 mm. A 36 steel is used…

A: Step 1

Q: 14: In the tension member connected to a gusset plate as shown below. Determine the valu

Q: Determine the effective net area using the U values given on Table 3.2 An MC12x45 is connected…

Q: a. Prepare a table showing values of Group A bolt shear strength and slip-critical strength for…

A: Shear strength: The maximum load that can be resisted by the structure is known as shear strength.…

Q: The tension member shown below contains holes for %" dia. bolts. At what spacing, s, will the net…

A: Diameter of bolt = 0.75"

Q: a 3" oj ob C" OC 5" of od 3" e = 4" A" B" | A" B" A" B" The holes are for 1-inch-diameter bolts.…

Q: Hhello, Thanks a lot for your help, please I have the following points: 1-Is it allowed to use…

A: Design of tension member

Q: 3. A Channel section is connected to a 10mm gusset plate with 20mm- diameter bolts as shown in the…

Q: 2. Determine the number of shear planes, the bolt hole diameter, and the minimum bolt pretension for…

A: The diagram is given in the above figure. Lap joint is used with M16 grade 10.9 bolts. We have to…

Q: Problem 2: For the Channel as shown in the figure below determine the design and allowable strength.…

A: We have to determine the value of design and allowable strength. The holes are for 18 mm diameter…

Q: An air chamber is held together by bolts. d = 20 cm, D = 40 cm. A-A: 20 bolts, Drolt = 2.5 cm. %3D…

A: Given : If 2.5cm of 20 bolts are able to hold at A-A. D=40cm, d=20cm, D=2d

Q: The plate splice shown in the figure below has 9 – 3/4 inch diameter A325-N type bolts (Group A, N…

A: A325 N type of bolts, N indicates threaded portion will be in the shear plane. Dia of bolt = 3/4 in…

Q: he plate shown in the figure 2.19 has a thickness of 12 mm. Diameter of bolts is m. A 36 steel is…

A: t= 12 mmd= 16 mmFy = 248 MPa and Fu = 400 MPaThe standard nominal hole diameter of 16 mm bolts = 17…

Q: Determine the strength of the connection shown in Figure , based on bearing and shear, for the…

A: For both holes, calculating the bearing deformation strength:Rn=2.4dtFu =2.4(3/4)(3/8)(58) =39.15…

Q: Design a weld connection for an UNP 280×80×9 of S 355 (fy= 355 MPa and fu= 470MPa) steel connected…

A: UNP 280 *80*9S275t = 10mmfy=355MPafu=470MPaTo find:-Design of weld

Q: The tension member shown in Figure P3-14 contains holes for 7/8-in Ø bolts. At what spacing, s, will…

Q: Problem 4: In the tension member connected to a gusset plate as shown below. Determine the value of…

A: Width of member (B) = 400 mm Thickness of member (t) = 12 mm Diameter of bolt (d) = 30 mm From…

Q: ectional properties. For the bolt hole, add 1/8" to the bolt diameter.) (a) (c) L5x5x5 Weld PL 5×5…

Q: Find the available strength of the S-shape shown in Figure 3.20. The holes are for 3/4-inch-diameter…

A: Given : The S shape is shown below : Dia of holes = 3/4 in. Using A36 steel FInd - The Available…

Q: Compute the net area of each tension member. Note that for a standard-size bolt hole, hole dia =…

Q: GOmm 5omm 10omM 100mm 100mm EOmm 150mm

A: Diamter of bolt (d) = 33 mm Let's 2mm extra is provide in hole So diameter of hole (dh) = 33+2 =…

Q: Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in…

A: here given double angle sec so please keep this in mind for no. of bolt in net area calculations…

Q: What is the nominal, standard hole size for a 2" diameter bolt?

A: The correct answer is (a) 2.0625"

Q: Please answer this po, thank you so much!

A: Given data, Thickness of plate = t = 12mm Diameter of holes = dh = 18mm A50 steel is used , fy =…

Q: 20. determine the capacity of the details shown below. A992: Fy=50ksi, Fu=65ksi A36: Fy=36ksi,…

Q: PL 16x300 拓 C300x37 PL 16x300

Question

Compute the effective net area of the built-up section shown below if the holes are punched for 22mm bolts. Assume U=0.90. The relevant data are Ac=4,735.00 mm2 for each channel, tw=9.8 mm, tf = 12.7 mm. (Key Answer: 14,580.00 mm2)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A double lap splice connection shown in figure B is made up of 6mm x 150mm and 9mm x 150mm. Use NSCP specifications and assume a double row of bolts with standardsize holes for a bearing type connection with threads excluded from the shear planes.Minimum tensile strength Fu = 552.93MPa. Assume diameter hole is 3mm bigger than thediameter of bolts. Allowable shear stress is Fv = 207MPa. Allowable bearing stress fb = 1.2Fu.Diameter of bolts is 19mm. Fy = 449.25MPa.(a) Compute the tensile capacity of the steel plates. (Max. Net Area = 0.85 of Gross Area)(b) Compute the number of 19mm diameter bolts to develop the full strength of the plates. Note: SHOW DRAWINGS AND SOLUTIONS.
Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 1. The gross and net areas Ag and An.
Determine the effective net area of a W 360 x 91 shown. The holes were punched for M20 bolts. 65 mm 0000 P O O DO 65 mm 60 85 85 85 mm mm mm mm
1. Compute the critical net area of the 12-mm thick plate shown using AISC NSCP 2015 Specs (Section 504.3.2). The holes are punched for 19-mm bolts. Note that for a standard-size bolt hole, hole dia = bolt dia (in mm) + 3mm or hole dia. = bolt dia (in inches) + 1/8in. 25 mm 75 mm 275 75 m 25 m 75 mm 2. Determine the critical net area of the W12 x 16 shown in the figure, assuming that the holes are for 1-in bolts. 3 in W12 x 16 BỘ 3 in d = 12.00 in-0.220 in 3 in DO 3 in E by- 3.99 in+ 2 in 2 in 3. Determine the critical net area of an L8 x 6 x1/2 with staggered holes in each leg as shown in the figure. Holes are for 7/8-in diameter bolts. 2 2 4 @ 11 L8 x 6 x 2
Two 10inch-15.3 lb channels are welded together as shown in the figure. Compute for the values of Centroids, and lxx for the figure. 1. Determine ybar? 2. Determine lxx (Centroidal)
Please answer with complete details. Thank you. A = 1 B = 1 C = 2
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
Calculate the maximum tensile load, Ta or Tu of the connection shown in Figure 7. Theconnection consists of two 3/8" plates fastened to each side of one 13/16" plate.Assume 7/8" diameter bolts and standard punched holes. Use A36 steel. The plate is 13” wide. Note: Be sure to check all failure modes; bolt failure modes, and member failure modes(including block shear)
1
For the following plate calculate the net section failure resistance. Assume plate thickness as 13mm and Fy=300MPa and Fu=440MPa. (Dimensions in mm) Bolts: M20- Punched 1- 300 13mm Plate 65 -+ 65 100 70 Q² 55-45-