Compute the discharge over a Cipolleti weir 5.0 ft long under a head of 0.85 ft. Compare with the discharge over a standard rectangular weir with the same length and head.

Q: ). Find the discharge over a 60-degree V-notch weir if the head is 6.25 inches.

A:

Q: 5. What is the flow rate of water over a 60° triangular weir when the head is 0.90 ft?

A:

Q: The head of water on a 90° triangular weir is 0.725 ft .Compute the discharge by a) Approximate…

A:

Q: Determine the discharge, in L/s, over the weir having a head of 0.30 m if a a contracted rectangular…

A:

Q: A sharp-crested weir 2 ft high extends across a rectangular channel 8 feet wide conducting…

A:

Q: if crest is 600 mm long and the water surface at point 2.5 meters upstream from weir is 140 mm…

A: Given DataL=6 mH1=depth of water=2.5 mH=height of water above crest=0.140 mDischarge over a…

Q: 2. Determine the discharge of the weir having a head of 1.2 m in L/s a) If a 90° triangular weir is…

A:

Q: 2. Determine the (a) actual discharge, (b) theoretical discharge and (c) weir coefficient over a 90°…

A: As per guidelines we can solve one question at a time, please upload separately,Thanks Solution…

Q: Problem 4: Find the discharge in a 80 degrees triangular weir with a head of 1.8 ft over the weir.…

A:

Q: A rectangular weir is doubly contracted with a width of 1.44m and a flow depth of 0.50m above the…

A: The values given in the question are as follows: Width of rectangular notch(B)=1.44 m Flow depth of…

Q: rectangular weir is doubly contracted with a width of 1.40m and a flow depth of 0.43m above the…

A:

Q: Ozark Underground Laboratory has a 45 triangular weir constructed using 2 thresher blades that can…

A: Given data, Maximum flow Q = 120 cfs Notch angle θ = 45o

Q: The head over a 90° V-notch weir increases from 0.15 m to 0.3 m. The ratio of new discharge to the…

A:

Q: A sharp-crested rectangular weir 1 m long with end contractions suppressed and a 90˚ V-notch weir…

A:

Q: 10. Find the discharge over a cipolletti weir of length 1.3 m when the head over the weir is 0.65 m.…

A: This question is related to the Fluid Mechanics from Civil Engineering. In This question we…

Q: What is the head (m) on a V-notch weir (Ca=0.58) for a discharge of 225 liters/s (a) if the opening…

A: Given Data:Cd=0.58Q=225L/sec=225×103 cm3/secQ=0.225m3/sec

Q: A sharp-crested suppressed rectangular weir 1m long and a standard 90- degree V-notch weir are…

A: Given    Length of rectangular weir = 1m

Q: Problem Solving: Determine the flow rate over a suppressed weir if the weir crest is 24 in. long and…

A: Given data in question  Length of crest weir Head To find out  Discharge

Q: Determine the discharge over a standard contracted weir when the upstream water depth is 2.1 m. The…

A: Step 1

Q: with no end contractions were to replace the triangular weir, what would be the required H in

A:

Q: A rectangular weir is doubly contracted with a width of 1.35m and a flow depth of 0.39m above the…

A:

Q: What is the discharge over a cipolletti weir of length 3m when head over the weir is 1 m (Cd = 0.62)…

A:

Q: A trapezoidal weir of length 4 m and sides inclined 1 horizontal to 1.5 vertical discharges 12 m³/s.…

A:

Q: 1. On a 90-degree triangle weir, the measuring head of water is 600 mm. What length of Cipolletti…

A: Given Data:90° triangular weirθ = 90°water head = 600mm=0.6m

Q: A weir in a horizontal channel is 12 ft wide and 4 ft high. The upstream water depth is 5.2 ft.…

A:

Q: Show complete solution. What length of Cipolletti weir should be constructed so that the head will…

A: What length of Cipolletti weir should be constructed so that the head will be 3.75 ft when the…

Q: A contracted measurement weir is to be installed in a 22-ft-wide channel. The depth of the weir…

A: Given data : Width of channel = 22 ft Depth of weir opening = 16 inches Average flow = 6 MGD Minimum…

Q: The depth of water over the weir was 5m. If the total discharge through the weir was  1,000,000 m3,…

A: Given data,  Depth (H) = 5 m Discharge = 1000000 m3 Length = 200 m

Q: Calculate discharge for a rectangular Sarda fall having Crest length 10 m Top width 3m and Depth of…

A: Sarda fall  Sarda-type falls are made up of modest falls that result in slow energy dissipation of…

Q: Determine the discharge, in L/s, over the weir having a head of 0.30 m if a a contracted rectangular…

A: Given Data:Weir head = 0.30mLength = 2m It is required to calculate the discharge in L/S over the…

Q: What length of a Cipolletti weir should be constructed in order that the head of flow will be 0.96m…

A:

Q: What is the head (m) on a V-notch weir (Cd = 0.58) for a discharge of 225 liters/s (a) if the…

A:

Q: A weir is to be installed to measure a flow of 0.80 m3/s. If the maximum (total) depth of water that…

A: Given Q = 0.8 m^3/s w = 4 m total height = 1 m

Q: The length of a Cipolleti weir is 5 times its head. If the flow in the weir is 0.60 m3/s, what is…

A: Given data- Length of a Cipolleti weir is 5 times its head. The flow in the weir is 0.60 m3/s

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.