Compound axial member ABC has a uniform diameter of d= 1.50 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 - 90 in. • Segment (2) is a copper [E2 - 17000 ksi] alloy. The length of segment (2) is L2 = 126 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2- 2100 µin./in. in the longitudinal direction. What is the total elongation of member ABC?

Compound axial member ABC has a uniform diameter of d= 1.50 in. • Segment (1) is an aluminum [E1 = 10000 ksi] alloy. The length of segment (1) is L1 - 90 in. • Segment (2) is a copper [E2 - 17000 ksi] alloy. The length of segment (2) is L2 = 126 in. When axial force Pis applied, a strain gage attached to copper segment (2) measures a normal strain of ɛ2- 2100 µin./in. in the longitudinal direction. What is the total elongation of member ABC?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The Brinell's hardness number (B.H.N.) is expressed as P (b) TD TD D-VD²-a² D+VD² -d² (c) (d) P TD D-VD? -d? TD D+\D² - d² where, P= Test force (M), D = Diameter of steel ball (mm), d = Mean diameter of the indent (mm) %3D %3D
The lowest stress at which permanent .deformation can be measured
In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to increase 50 x 10 mm while -3 those at CD decrease 60 x 10 nm in the 210 mm gage length Using E 140 GPa, determine the flexural stress at the top fiber. Answer must be in MPa. Given: a 50 mm, b 130 mm, and c 80 mm. gage length la mm omm c mni
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
The following information about the o-e curve is given for a steel alloy. E = 0.001527 at o = 300 MPa and ɛ = 0.003054 for o = 600 MPa. (a) Draw the stress-strain diagram and calculate the E for this alloy.
At room temperature (20°C) a 0.7-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 150°C, determine: (a.)The normal stress in the aluminum rod, (b.) The change in length of the aluminum rod. 0.7 mm 300 mm A Aluminum A =2,000 mm² E= 75 GPa α = 23 x 106/°C 250 mm B Stainless steel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C
At a certain point in a structural member, the value of ox = -45 N/mm², ay = 75 N/mm² and t = 45 N/mm2. The principal stresses will be
A mild steel flat of width 120 mm and thickness 10 mm is bent into an arc of a circle of radius 10 m by applying a pure moment 'M'. If E is 200 GPa, then magnitude of the pure moment 'M' will be
Urgent. a = 10 , b = 7 solve this question about those information.
Which of the following parameter represents principal stresses: T_a none of the available option O_X O_y 0_a
Narrow bars of aluminum are bonded to the two sides of a thick steel plate as shown. Initially, at T₁ = 70°F, all stresses are zero. Knowing that the temperature will be slowly raised to T₂ and then reduced to T₁, determine (a) the highest temperature T₂ that does not result in residual stresses, (b) the temperature T₂ that will result in a residual stress in the aluminum equal to 58 ksi. Assume aa = 12.8 x 10-6/°F for the aluminum and a = 6.5 × 10-6/°F for the steel. Further assume that the aluminum is elastoplastic with E = 10.9 × 106 psi and ay = 58 ksi. (Hint: Neglect the small stresses in the plate.) Fig. P2.121
Question 2) Knowing that a 0.02-in. gap exists when the temperature is 75 °F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. -14 in. Bronze A = 2.4 in² E = 15 x 10 psi a = 12 x 10-6/°F -18 in.- Aluminum A = 2.8 in² E = 10.6 x 105 psi a = 12.9 x 10-6/°F