Compare the compound and shunt motors by filling in the correct answer on the blanks. a) Starting current: The compound motor has a (higher/lower) starting current than the shunt motor. b) Starting torque: The compound motor has a (higher/lower). starting torque than the shunt motor. c) Efficiency: The compound motor has a (higher/lower) efficiency than the shunt motor. d) Speed regulation: The compound motor has a (higher/lower) speed regulation than the shunt motor.

Compare the compound and shunt motors by filling in the correct answer on the blanks. a) Starting current: The compound motor has a (higher/lower) starting current than the shunt motor. b) Starting torque: The compound motor has a (higher/lower). starting torque than the shunt motor. c) Efficiency: The compound motor has a (higher/lower) efficiency than the shunt motor. d) Speed regulation: The compound motor has a (higher/lower) speed regulation than the shunt motor.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter43: About Dc Motors

Section: Chapter Questions

Problem 1SQ

See similar textbooks

Similar questions

12- Starting torque of induction motor is less than that of a. DC shunt motor b. AC series motor c. DC compound motor d. DC series motor
Q2] Fill in the blank (9 Marks) 1-The current drwan by the armature of D.C. motor is directly proportional to 2- The speed of a D.C. shunt-wound motor will shunt field regulator is increased. 3- The synchronous speed of a three-phase induction motor is number of pairs of poles. Rotor copper losses Rotor input power in induction motor = 5- A 4-pole three-phase induction motor has a synchronous speed of 25 r.p.s. The frequency of the supply to the stator is_ Hz. 6- The power input to a mains transformer is 200VA. If the primary current is 2.5A, the secondary voltage is 2V and assuming no losses in the transformer, the turns ratio step down. is 7- A 200kVA transformer has an iron loss of 1 kW and full load cu loss of 2 kW. Its load kVA corresponding to maximum efficiency is kVA. 8- If cu loss of a transformer at 7/8th full load is 4900 W, then its full-load cu loss would be watt. 4- if the value of resistance of the proportional to the 9- The slight curvature at the lower end of the open…
P-1).. Which of the following determine the amount of torque produced by a single-phase split-phase motor? a) The strength of the magnetic field of the stator b) The strength of the magnetic field of the rotor c) The phase angle difference between the current in the start winding and the current in the run winding d) all of the above P-2). The phase angle difference between the currents in the start winding and run winding of a single-phase split-phase motor is typically 90 degrees. a) true b) false P-3). A centrifugal switch is used to disconnect the________ winding of a non-hermetically sealed single-phase split-phase motor at approximately 75% of rated speed. a) run b) start c) either "a" or "b" d) neither "a" nor "b" P-4). Where an internal centrifugal switch cannot be used, an external______ relay can be used to perform the same function in a single-phase split-phase motor. a) hot-wire b) current c) solid-state starting d) all of the above
A 460-V. 25-hp. 60 Hz. four-pole. Y-connected induction motor has the following impedances in ohms per phase referred to the stator circuit: RI = 0.641 ohm X1 = 1.106 ohm R2 = 0.332 ohm X2 = 0.464 ohm XM= 26.3 ohm (a) What is the maximum torque of this motor? (b) At what speed and slip does it occur? (c) What is the starting torque of this motor? (d) When the rotor resistance is doubled. what is the speed at which the
A 220 V shunt motor driving its normal load draws an armature current of 50 A from a 220 V dc source. The armature resistance of this motor including brushes is 0.25 ohms. How much armature current (minimum) Will this motor draw from a 200 V DC source when driving the same load with the field adjusted to maintain the same speed.
Fill in the following blanks 1.In order to have sparklesscommutation, the brushes should be placed along................. 2.D.C. series motor are used in those applications where...............starting torque is required
What are the effects of slip in the slip-ring induction motor? A. No effects B. Changes the change in speed C. Changes the rotor frequency D. B and C
Question 6 A universal motor is a single phase AC motor with series motor characteristics. a. Sketch the equivalent circuit of universal motor b. Is it possible universal motor runaway like series DC motor at no-load operation? Explain the behaviour of the motor. c. How can you build a dynamic mathematical model for universal motor? Explain with the related equations Full explainthe this question very fast solution sent me step by step Don't ignore any part all part work u a to b and c Text typing work only not allow paper work
Name the type of three-phase induction motor, which is used for high starting torque application a. Single phase induction motor b. DC motor c. slip ring rotor d. Squirrel cage rotor
L-1). The 3-phase wound-rotor induction motor has .... . a) high starting torque b) low starting current c) both "a" and "b" d) neither "a" nor "b" L-2). The 3-phase wound-rotor induction.........a) motor has a wire wound rotor b) motor's rotor can be connected to an external resistive load by way of slip rings and brushes c) motor requires more maintenance than the 3-phase squirrel-cage induction motor d) all of the above L-3). The 3-phase wound-rotor induction motor's rotor circuit's resistance should be adjusted so it is__________ during starting. a) low b) high c) either "a" or "b" d) neither "a" nor "b" L-4). Will a 3-phase wound-rotor induction motor start with no external circuit connected to its rotor leads? a) yes b) no
4- A 3-phase A -connected 220-V (line-to-neutral), 60-Hz 6-pole induction motor has the following parameter values in O/phase referred to the stator: R1 = 0.294, R2 = 0.144, X, = 0.503, X2 = 0.209, Xm= 13.25. The total friction, windage, and core losses may be assumed to be constant at 403 W, independent of load. For a slip of 5%, a. Output torque b. Stator current, c. Power factor, d. Converted power e. Efficiency.
A d.c. shunt motor is running with certain load. The effect of adding an external resistance in parallel with field circuit is to stop the motor increase the motor speed reduce the armature current of the motor Reduce the motor speed O