Co D N B F 500 mm E A 250 mm 300 mm

Q: What is section modulus?

A: The section modulus helps to calculate the outermost stress in the beam section. It is numerically…

Q: Q5: At the instant shown in figure (5) 04 = 6 rad/s, pulley A is given an angular acceleration a =…

A: Given data: The radius of the pulley A is rA=60 mm=0.06 m The initial angular velocity of the pulley…

Q: 90mm 60mm 45mm R15mm

A: Let’s divide the given section into 3 sections. Section 1 is a rectangular OABC. Section 2 is the…

Q: Question 29 Which of the following can change the hardness of a material? O Manufacturing process O…

A:

Q: dy = m y2 dx

A:

Q: Calculate the maximum tensile and compressive stresses in the brass and aluminium.

A: A composite beam is formed with more than one material to increase its load resistive strength. When…

Q: 80mm 60mm Vax's Gomm 40mm Find the location of the Controid. Show All work. 1

A:

Q: In the figure shown, compute the following : 75 mm 75 mm E 75 mm-

A: Given Shaded area To find Centroid X axis Centroid Y axis

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Q4 The L2 steel bolt as shown in Figure Q4 has a diameter of 5 mm, and the link AB which is made…

A:

Q: Find the following. Show complete solution.

A: The given diagram is here, Section 1:- A rectangle OABC, whose sides are 120 mm and 80 mm Section…

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: Determine the maximum deflection of the 70-mm-diameter A-36 steel shaft.

A: To find: The maximum deflection of the 70 mm diameter steel shaft. Given: The diameter of a steel…

Q: 300 mm 30º 300 mm 300 mm Can someone please label the projection of F and the rest of the…

A:

Q: write any 10 mechanical propeties of mild steel. Also expplain each one by one

A: 10 Properties of Mild Steel  1.Ductile material:- Can easily convert into thin sheet. 2.Easily…

Q: The first moment of an area (mm3) about the x-axis (Qx) is O 462,000 O 594,000 O 246,000 864,000

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: rof. Eduardo Stefanelli www.stefanell.eng.br 0 5 10 45 40 35 30 12.4 mm

A: The Screw gauge is given.

Q: Draw chalk diagram of all sections

A: To draw section views

Q: how 79x10^3 get? or where did the 79x10^3 came from?

A: G = shear modulus of the hollow shaft

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: 120 mm 60 mm 90 mn D 80 mm C 45 mim 480 N

A:

Q: m. nd Find the components of the equivalent force. Express the re Express the z, y, and z components…

A: The position vectors are-

Q: 10 1 R6 1 10 20 50 30 R10 -5 X 45.00° 50 1 1 5 15 5 R30 110 R5 55 20 R6 7 8 60 30 -60 店 06-4 holes…

A: Step 1: First create following top view and extrude it up to required depth i.e. 60 mm

Q: determine and plot the moment M rotate arm 0A over the range 0 < Find the maximum value of M and

A:

Q: Calculate the linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

A: To find - The linear speed of the needle at the instant that theta equals 30 degrees and the wheel…

Q: Q.1) Knowing that the tension in cable BA is 570 N, determine the moment about O. Neglect the…

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: 2 Brass expands more than iron when heated. How would the strip look after prolonged exposure to…

A:

Q: 5 kip/ft 15 kip ft 15 kip · ft B- 6 ft 10 ft 6 ft

A: Given figure:

Q: 100 mm 100 mm 10 mm 10 mm. 200 mm 100 mm f 10 mm I II

A: For the selection of sections, we have to calculate the maximum bending stress in the beam. From the…

Q: If FB = 830 N, Fc = 450 N, determine the magnitude of the resultant force at A. (Figu Express your…

A: Given FB=830NFC=450N

Q: The rectangular lamina with breadth = 60 mm, depth = 30 mm. The Ixx value is _____________ mm4…

A:

Q: 8. For the cross-section of a beam shown; a) locate the centroidal axis from the bottom of the…

A:

Q: Both pulleys are fixed to the shaft and as the shaft turn with constant angular velocity, the power…

A: power of pully A= power of pully BGiven θ= 0°(T1-T2)×RA =(T3-T4)×RB(80-65)×40…

Q: The handle of the hammer is subjected to the force of 35 Ib. The moment of this force about the…

A:

Q: 500N 100N 300mm 800 N 900 N 28°

A:

Q: A 100 ma 100mm Thok 100mm mm ; 100 mm, A=200mm E = 2006 Pa find 200 KN As 400mm? Reactions с

A:

Q: 300 N 36 mm

A: We need to apply force equlibirium equation along the horizontal direction∑Fx=0Ax-C=0......consider…