closed horizontal cylindrical tank 2.0 m in diameter and 3.5 m high is completely filled with fluid whose specific ravity is 1.3. If the allowable force at the rear wall of the tank is 85 kN, how fast can the cylindrical tank be ccelerated horizontally along its longitudinal axis in meters per second squared? 1.122 B. 4.928 C. 5.946 D. 3.144

closed horizontal cylindrical tank 2.0 m in diameter and 3.5 m high is completely filled with fluid whose specific ravity is 1.3. If the allowable force at the rear wall of the tank is 85 kN, how fast can the cylindrical tank be ccelerated horizontally along its longitudinal axis in meters per second squared? 1.122 B. 4.928 C. 5.946 D. 3.144

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The space between two plates (20cm*20cm*1cm), 1 cm apart, is filled with a liquid of viscosity 1 Poise. The upper plate is dragged to the right with a force of 5 N keeping the lower plate stationary. What will be the velocity in m/s of flow at a point 0.5 cm below the lower surface of the upper plate if linear velocity profile is assumed for the flow? 20 cm 1 cm O 0.25 m/s O 1.25 m/s O 2.5 m/s O 12.5 m/s F,
Q3) A closed 0.4 m diameter cylindrical tank completely filled with oil (SG=0.9) rotates about its vertical longitudinal axis with an angular velocity of 40 rad/s. Determine the difference in pressure just under the vessel cover between a point on the circumference and a point the axis.
The clearance space between a shaft and a concentric sleeve has been filled with a newtonian fluid the sleeves attains a speed of 60 cm/s when .a force of 500 N is applied to it parallel to the shaft. what force is needed if it is desired to move the sleeve with a speed of 300 сm/s?
A 1.5 m diameter open vessel, 2m high is filled with oil s.g= 0.85 at a depth of 1.6m and rotated at 47 rpm. a. what is the resulting depth of liquid at the center of the vessel? b. what angular speed should be imposed on the vessel such that the liquid touches the bottom surface of the vessel at the center? c. What angular speed should be imposed on the vessel such that there is no liquid 0.47m from the v ertical axis of the vessel?
An open tank 3m by 3m in horizontal section weighs 4 kN and contains water to a depth of 1m. It is acted by an unbalanced force of 18 kN parallel to the pair of sides. a) Determine the acceleration of the tank. b) What must be the height of the tank so that no water will spill out? c) If the acceleration is increase by 4m/s2 , how much water will spill out?
Situation 4: An open horizontal tank 2 m high, 2m wide and 4mlong is full of water. Determine the amount of water spilled out when the tank is accelerated horizontally at 2.45 m/s in a direction parallel with its longest side in m?. Find the force acting on the side with the greatest depth in kN. 9. 10.
The 8 mm gap between two large vertical parallel plane surfaces is filled with a liquid of viscosity 2x10-2 Ns/m². A thin sheet of 1 mm thickness and 150 mm x 150 mm size, when dropped vertically between the two plates attains a steady velocity of 4 m/s. Which nearly gives the weight of the plate in Newton. Assume that the plate moves centrally. O a. 0.87 O b. 1.25 O c. 2.10 O d. 1.03
Two blocks (A and B) are colliding as shown below. Block A is 15kg and Block B is 10kg. Given that block A is at rest and Block B is moving toward Block A at a speed of 15m/s, what should be the maximum displacement of the spring after impact if the two blocks will be joined together by the hook. 15 m/s k = 10 kN/m A В
QUESTION 4) Calculate the 12kN/m support reactions and hinge force in the system shown in figure. 6771 H 3m B 3m OG 10kN 4 5kNm A
Q7- Air flowing with a Mach number of 2 with a pressure of 80 kPa and a temperature of 30 °C passes over a component of an aircraft that can be modeled as a wedge with an included angle of 8° that is aligned with the flow, the flow is turned through an angle of 4 leading to the generation of an oblique shock wave. Find the pressure acting on the surface of the wedge. M 2 P = 80 kPa T = 30°C
A tanker contained with water is pushed horizontally at constant acceleration of 5.0 m/s?. If the tank is 10 m long and the depth of the water is 3 m when at rest, Calculate; a) The angle of water surface to the horizontal. b) The maximum pressure intensity on the bottom How far below the water surface should the top side of a vertical square 1 m on each side should be immersed so that the center of pressure will be 70 mm below the center of gravity? complete solution needed
An open horizontal tank, 1.5m high, 2m wide and 5m long is full of oil (sp gr= 0.9). It is accelerated in the direction parallel to the longer length at 2.3m/s^2. What is the force acting at the wal of the tank with the shortest depth in kN?