The 2-m-wide rectangular gate in pinned at its center A and is prevented from rotating by the block at B (Figure 1) p = 1.0 Mg/m² Suppose that a = 17 m Figure FB = O HA 1 of 1 Value ▾ Part A Submit Request Answer Determine the magnitude of reaction at due to hydrostatic pressure Express your answer to three significant figures and include the appropriate units. Value Determine the magnitude of reaction at B due to hydrostatic pressure. Express your answer to three significant figures and include the appropriate units. Submit Request Answer Units 4 → SWE ? Units ? Revine جائے

Q: Determine maximum principal stress

A: Given data : Normal stress in X direction σX=-320 MPa Normal stress in Y direction σY=240 MPa Shear…

Q: buoyant force acts in the direction opposite the force of

A: Buoyant force is the upward force exerted by fluid on object when it is submerged fully or partially…

Q: 米 Ax c 所 个 Ay Icy Cx→. C

A:

Q: 1000 lb 1000 lb G 1000 lb 130° A go D 10 ft 10 ft -10 ft- -10 ft- 1000 lb

A: Apply equilibrium condition : ∑ME=0RAY×40-1000×10-1000×20-1000×30-1000×40=0RAY=2500 lb

Q: Problem The two springs are identical, with unstretched lengths 250 mm and spring constants k = 1200…

A:

Q: 1. Reaction in point( a) and (c). 2. Draw the share force diagram 3. Draw the bending moment diagram

A:

Q: The pressure head is in the capillary fringe zone, in the root zone, and in the saturated zone. O a.…

A: Answer Capillary fringe zoneThe capillary fringe zone is known as the subsurface layer by which the…

Q: IT= 30,kN 20 kN 20 kN/m 60 kN.m 30 kN.m 3 m 2 m 2 m 4 m 4 m find the reaction forcse with force…

A: To find the reaction forces

Q: E 20 k 12 ft 12 ft 5 k -5 ft-5 ft- -14 ft-

A:

Q: The assembly of pipes consists of galvanized steel pipe AB and BC connected together at B using a…

A: Given data: Length of pipe (AB)1=1m Inner Diameter=17 mm Outer diameter=20 mm   Length of pipe(BC)…

Q: 5 ft 500 lb B 5 ft 1500 lb C 2 ft 5 ft D

A: From the given figure it is required to calculate the unknown forces.

Q: Classify the STABILITY and DETERMINACY of the following structures below. Identify the degree of…

A: As per the guidelines we are supposed to solve only first 3 subparts for multiple subpart asked....…

Q: Find the support reaction at roller support A

A:

Q: Description Draw the FBD. Then, determine the reactions at A and B. 650 N 500 N 30° 300 N 1500 N · m…

A:

Q: Determine maximum principal stress

A: Given data : The value of normal stress in X direction σX=150 MPa The value of normal stress in Y…

Q: me the reactions at the supports. - 4 m 500 N/m 30 4 m

A:

Q: X kN Y kN/m 4 A 2m 2m 1. What is the vertical reaction at the hinge support? (kN) 2. What is the…

A: Given data in question  UDL Point load Angle of inclination  Span member length To find out…

Q: Calculate the magnitude of the shear force (kN) V at a cross-section just to the right of the 6.0 kN…

A: Solution

Q: Determine the reactions at A, F, and E. 0.5 m E C 0.5 m 200 N B 0.8 m 0.6 m 2 m

A:

Q: From the figure below, determine reaction Ch

A: Support reaction: Apply equilibrium condition ∑MC=0AV×8-45×4=0AV=22.5 KN∑FY=0AV+CV=022.5…

Q: मित 4KN 8KN 1m 12m 1m HINGE 2m 6 KN 2m 10KN 3m 5m

A:

Q: Draw the FBD. Then, determine the reactions at A and B. 650 N 500 N 30° 300 N 1500 N · m 60° B -5 m-…

A:

Q: Calculate the reactions at the both ends

A:

Q: A stepped column carries loads as shown in the figure. What is the maximum normal stress in the…

A:

Q: Locate the center of gravity of the volume. The material is homogeneous.

A:

Q: Determine the reactions at A and B 600 N/m 900 N•m В D 1 m 1 m 1 m C

A: Given,

Q: B. The three bars supported a concrete beam weighing 50 kN. The length of steel is 0.50 m. Based on…

A: The given data is shown below: Weight of beam=50 kNLength of steel=0.50 mTemperatures=20°C and 30°C

Q: The truss shown in the figure is supported on a roller at B and a hinge at A. Solve for the reaction…

A:

Q: A. Determine the determinacy and stability of the following structure. Hinge Hinge (a) (b) (d) (c)…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Situation A (1 - 4) A cylindrical pressure vessel is constructed from a long, narrow steel plate by…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?