6 x 2/ Given in the design of the followingmovable grid system: field dimensions(360m x 1080m), soil mixture alluvial,effective depth of root zone (80 cm), Germanconsumption (8mm / day), sprinklers(Jism and 9m), average Wind speed (2m /sec), water holding capacity (1.7mm /cm), moisture depletion rate (50%), baseinfiltration rate (10.2mm / hr), note that theirrigation efficiency is (659). The main pipepasses outside the field. The spray tubeis made of Aluminum material dischargecoefficient (0.967 = c) required:. 1. Netirrigation depth 2- Irrigation interval 3- Totalirrigation depth 4- Irrigation rate b) Numberof spray tubes needed for the field c)Sprinkler drainage, spray diameter, pressurecharge rate d Diameter of spray pop in cases:6 1- Spray pop Hesto 2 The spray pop hasa downward slope of (19). 3- The spray pophas a slope of (19). The pressure charge atthe entrance and end of the spray tube for thethree cases in d%3D

Given that field dimensions are 1080 m x 360 m Depth of the root zone is 80cm Water consumption =…

Answered: 6 x 2/ Given in the design of the…

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

3. Answer the question completely and write down the given, required and formula that had been used. Provide graph and accurate/comple solution. The value are: V- 1 X- 5 W- 7 Y- 6 Z- 8
QUESTION 4 Find the resultant vectors. This referes to Question 4 on the PDF v Horizontal 3ON and Vertical 60N A. 67.1N @ 116.6 below the horizon v Horizontal 3ON and Velucal -60N B. 67.1N @ 63.4 above horizon v Horizontal -30N and Vertical 60N C. 67.1N @ 243.4 from the horizon v Horizontal -30N and Vertical -60N D. 67.1N @ -63.4 below the horizon
Solve this pls. Same problem with different values already solved on bartleby. You can use it for reference. Here's the link :
Given: The plane accelerates in its current trajectory with a= 100 m/s^2 Farag Angle theta= 5° W=105 kips F_drag= 80 kips m= 1000 lbs Find: F_thrust, F_lift Please include the KD. Fthrust Futel t Fueight 000 BY NC SA 2013 Michael Swanbom
A rectangular tube of outer width w = 7.5 m, outer height h = 5 m and thickness t = 0.17 m experiences bending through the x axis. What is the moment of inertia of the cross-sectional area In? y -- X MATLAB input variables: format shortEng W = 7.5; h = 5; t = 0.17; moment of inertia I, = m4
GIVE ME THE COMPLETE SOLUTION FOR THISTHIS IS THE ANSWER ACC TO THE ANSWER KEY I JUST NEED HELP FOR THE SOLUTION Theta3/T = ((5*s^2 + 9*s + 9))/(15*s^5 + 47*s^4 + 117*s^3 + 161*s^2 + 81*s)
Parts for each product Homework 1 n produce dryer plant Can for each product castiens Then each product is assembled in its dedicated washing and dryer A machines. Difterent are manufactured by press and motor ly sechon. The the monthly capacity of different sections are: washing machine or looo dryer machine Press section: 100 - Motor section: 1600 washing machine or 7o00 drjer machine machine assembly line: goo0 machine washing druer machine assembly line: 5000 machine washing 1, profit for each unct of washing and dryer machines is 270 and 300 respectively. Formulate a linear programming problem for Find ing how many washing and dryer machines should be produced many washing to maximize total plant's profit. 2.A A Post Company need to transfer 30000 boxes with two each truck presented of olifferent trucks. Chavactenistics problem for The table below. Formulate a linear programming each truck to optimum nunber of minimIze total Cost.
(i) 450 cm²/(5s)* (b) Figures Q.1(b)) and Q.1(b)(ii) show two sets of vectors. Using triangular method (triangle rule), draw corresponding resultant vectors R M+N+0 and R Q R S Figure Q.1(b)(i) L R Figure Q.1 (b)(ii) (c) Examine the magnitude and coordinate direction angles of the resultant of the two forces acting at point A as shown in Figure Q.1(c).
Q3: Find Req. between points (A&B) in the network in fig.(3). (25 mark) 22 42² lon 8r Fig.3 m 36₁ A B
Sketch the Isometric and three view and mention the dimensions Also draw the hidden lines, use creo parametic to sketch the figures 3.00 4.50 1.50 1.25 A -.25 4.00 Ø.78 3.00 .25 - .78- .40 A (BOTTOM) 4.50 2.25 4.50 1.00 МATL—AISI С-+1040 Step bracket.
YouTube Mall Over... Leeds International... M1 Questions by To... Question Completion Status: QUESTION 2 A car of mass 750 kg moves along a stretch of road which can be modelled as a line of greatest slope of a plane inclined to the horizontal at 30°. As the car moves up the roa for 500 m its speed reduces from 20 ms-¹ to 15 ms-¹. Calculate: a the loss of kinetic energy of the car 65,625) 66,625 67,625) O 68,625)
5. An engineer is planning to use gabion retaining wall to protect a section of Kennon road from landslide. A gabion is a wire mesh container filled with rocks. The engineer must estimate the volume of the rock to be used. If the gabion wall will have a thickness of 5ft, estimate the volume of the rocks given the measured depth of the wall every 10 ft of its width based from the road level. width, ft 10 20 30 40 50 60 70 80 90 depth, ft 5 12 20 18 17 13 10 5 a.) estimate the area of the wall using multiple trapezoidal rule with n=9 b.) estimate the area of the wall using single application of Simpson's 3/8 rule c.) estimate the volume of the rocks to be used using the area in a.) and b.)

SEE MORE QUESTIONS

Recommended textbooks for you

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

Principles of Heat Transfer (Activate Learning wi…

Mechanical Engineering

ISBN:

9781305387102

Author:

Kreith, Frank; Manglik, Raj M.

Publisher:

Cengage Learning

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L

SEE MORE TEXTBOOKS