Problem 1: For the propped cantilever beam shown, compute the support reactions using the method of consistent deformations by taking the reaction at support B as redundant. Also, draw the shear and bending moment diagrams. Use deflection formulas to determine deflections at B. Assume that EI is constant along the beam. 6 k A 2 k/ft Ţ 20 ft B 6 ft C

Problem 1: For the propped cantilever beam shown, compute the support reactions using the method of consistent deformations by taking the reaction at support B as redundant. Also, draw the shear and bending moment diagrams. Use deflection formulas to determine deflections at B. Assume that EI is constant along the beam. 6 k A 2 k/ft Ţ 20 ft B 6 ft C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q/Using the method of consistent deformation, find support reaction of the frame shown; assume EI= constant. 10kN/m B A 5m C 3m
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
200mm Strain gauge F mun +100m 200mm- 4mm Strain gauge 4mm 12mm 12mm 4mm A small T-section is used in inverted positions as a beam and is shown in figure over a span of 400 mm. If due to the application of forces shown, the longitudinal strain gauge at F registers a compressive strain of 1500 microstraints, determine the magnitude of P. Take E = 200 GPa.
The beams described in the problems for Section 9.9 have constant flexural rigidity El. A simple beam AB of length L is loaded at the lefthand end by a couple of moment M, (see figure). Determine the angle of rotation 6, at support A. (Obtain the solution by determining the strain energy of the beam and then using Castigliano's theorem.) Mo B L PROB. 9.9-1 Step-by-step solution Step 1 of 5 A Length of the simple beam AB = L Couple of moment at A,= M, Angle of rotation at A= 0,
%3D QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the crss section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm 10 mm A-40 mm--r: 30 mm 30 mm 10 mm 10 mm
3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is a cantilever beam carrying a uniformly distributed load of 4 KN/m freely supported on beam AB. Beam AB is freely supported on each ends. E = 13.8 GPa for both beam. Neglect the weight of the beam. a. Compute the reaction at D. b. Compute the deflection at D. c. Compute the bending stress of beam CD. 4kN Im 4m 4m
Using the Method of Consistent Deformations and Beam Deflection Formula. A two-span continuous beam is loaded by a 20 and 40 kilopound (kip) force as shown in the figure. Assuming flexural rigidity as constant, determine the reactions at each support. Determine the vertical reaction at A. B & C (kips) and put a negative sign if the reaction is downward.
QUESTION 2. An oblique bending moment of M = 5 kN.m is applied on the cross-section of an aluminum beam as shown in the figure. (a) Calculate the maximum values of compressive and tensile normal stresses on the cross section. (b) Define the orientation of the neutral axis and draw on the cross-sectionç. M = 5 kN.m 30° 10 mm 40 mm y 10 mm At-40 mm-- 30 гу 30 mm 10 mm 10 mm
tate of Stress Caused by Combined Loadings Learning Goal: To use the superposition principle to find the state of stress on a beam under multiple loadings. The beam shown below is subjected to a horizontal force P via the rope wound around the pulley. The state of stress at point A is to be determined. 100 mm 15 mm 20 mm 200 mm 150 mm f 20 mm The dimensions are di - 2.15 m. d₂ = 0.5 m. -0.85 m d-285 mm and r= 150 mm The applied force has magnitude P=4.5 kN Part A-Support Reactions and Internal Loading C₁, C₂=₁ N=, V = ₁ M = Determine the support reactions C, and C, and the internal normal force, shear force, and moment on the cross-section containing point A. Express your answers, separated by commas, to three significant figures. ► View Available Hint(s) Submit Part B- Properties of the Cross-Section A= I= Q = Submit VAX IT VOC JA=.TA= What are the cross-sectional area, moment of inertia with respect to the neutral axis, and first moment of the area with respect to point A for the…
A beam of T-section is pin-joint supported at point A and simply supported at point B with an overhang section BC shown in Figure 2. The cross section has the width b = 65 mm, height h - 75 mm and thickness / -13 mm. (a) Determine the support reactions at points A and B. (b) With the aid of bending moment of diagram, determine the maximum tensile and compressieve stresses in the beam. P = 4.5 KN t = 13 mm L₁=1.25 m q=2 kN/m L -L₂=2.5 m- ™ B +4-43=1 -L3= 1.5 m- t = 13 mm h'= 75 mm b = 65 mm
For certain values of w and P, the maximum positive bending moment in the beam is +7044 lb-ft, and the maximum negative bending moment is -8873 lb-ft. The cross section of the beam is shown. The pertinent section properties of the cross section are e = 2.90 in., f = 1.30 in., and I,= 18.3990 in.4. Calculate (a) the maximum tensile bending stress and (b) the maximum compressive bending stress that is produced in the beam. Enter your answers with the appropriate sign. B D b d y
The strain in the x direction at point A on the A-36 structural-steel beam is measured and found to be εx = 217 x 10^6. Determine the applied load P. What is the shear strain γxy at point A?