Circuit Impedance Z = Phase Angle = arc cos R/Z = , Calculated Es = Calculated Ec = Calculated ER = Calculated E = V

Q: Determine the value of the current (I) and the drop voltage across the resistance (V1) Rs www 1502…

A:

Q: A 1-m length of tungsten wire draws 5 A when connected across a battery. The wire is then cut into…

A: The tungsten wire will have resistance, the above circuit can be thought of as if a battery is…

Q: 2. From the circuit shown, determine the resistance between terminals a & b. 20 150 100 100 80 200…

A:

Q: Find total resistance, current and voltage drops, and total current

A: The solution can be achieved as follows.

Q: In the following circuit using Kirchhoff's find:   a) The current in each branch of the circuit.…

A: Nodal analysis is a technique used to calculate the currents in all the paths. Kirchoff current law…

Q: Find the potential difference across each resistor in the figure below. (R₁ = 5.402, R₂ = 3.80 2, R₂…

A: We need to find out voltage across each resistor for given circuit.

Q: 4. Find the mistake from the circuit. How would you measure the voltage and current of the 3k Ohm…

A: Voltage  It is the potential difference between two points, which is defined as the work done per…

Q: If three resistance in parallel, R1=3 ohm. , R2=50 mohm, R3= 1 kohm. the total R is: O 1038 ohm O…

A:

Q: Question 2 [ Consider the following circuit and answer the questions below. A) B) C) D) A and B. 12V…

A: In this question We need to determine the equivalent resistance across the terminal A and B. And…

Q: A 5 Ohm resistor is in series with a parallel connection 3 Ohm and 2 Ohm resistors. Determine the…

A:

Q: Based on the figure, answer the following: What is the resistance across terminals 'c' and 'f'?…

A: In the question.    What is the resistance across terminals 'c' and 'f'? Explain   What is the…

Q: 2. What is the voltage loss (potential difference) in the entire circuit? Are the two resistors…

A:

Q: Calculate the resistance between the two corners of the same edge.

A:

Q: Find the currents passing through the points A, B, C and D in the electric circuit in the figure.…

A:

Q: In the following circuit using Kirchhoff's find: a) The current in each branch of the circuit. b)…

A:

Q: ANSWER IN ESSAY FORM What is the purpose of Multisim in terms of circuit creation in relation to…

A: We need to find the purpose of Multisim in terms of circuit creation in relation to Ohms law, and…

Q: 3) Find the power in each element in the circuit below. 1-1dA 10 V 4A 14A P 30 V 20 V 12 V 0.41

A:

Q: R1 =10 k ohm R2= 100 k ohm Vi= 0.2mV VA

A: According to the question we have to find the value of VA.

Q: HIH V1 12V Q1. V2 1kHz 5V 1 D1 R1 -1k0 L1 1mH XMM1

A: Mode of operation of diode Forward biased mode (Diode ON and  Forward current flow through it)…

Q: In the figure the current in resistance 6 is i6 = 1.33 A and the resistances are R₁ = R₂ = R3 = 1.56…

A: According to the question, for the given circuitWe need to find emf of the battery.

Q: current

A: Diode Ideally, diode is open circuited when reverse biased and short circuited when forward biased.

Q: Find Vout 5V 10 ohms ww 100 ohms ww Vout

A: In this case, the output voltage of the following circuit is to be determined:

Q: ia + 14 - 3kN. 2ia 5 mA( 1kN O A) 2.25 mW O B) 9 mW C) 1 mW D) 0.75 mW

A:

Q: Find the value of la through the middle resistor Rs using conversion of voltage and current source…

A: Given  R1 =12 ΏR2 =3 ΏR3 =6 Ώ V1 =84 VV2 =21 V

Q: What is the current, including direction, in the wire connecting points 1 and 3? Express your answer…

A: The given circuit diagram is shown below,

Q: Find the power absorbed of each resistor. Each resistor is 9k and the voltage across a and b is 10V.…

A:

Q: A resistor consists of 5 colour bands as shown in Figure la. Find the value of the resistance. [2]…

A: Resistance Color coding is the special method to label the resistor with its value. The resistor is…

Q: Find Vout 10 ohms SVMM 100 ohms + • Vout

A:

Q: A 12-V DC automobile head lamp is to be used on a fishing boat with a 24-V power system. The head…

A: Given     Rating of lamp ,P = 50W Voltage rating of lamp ,VL= 12V Available Voltage, V= 24 V

Q: a circuit has resistance of 25 Ohms and the current flows at 10 amperes. determine the voltage

A:

Q: If current source is replaced by resistance R then find the value of R, to maintain same current…

A: Given- Voltage V=230 V, Current I=10 A, Frequency f=50 Hz, Circuit is given. To Find- The value of…

Q: For given figure below, find the equivalent resistance between points a and b if R1 = 5.8 Q, R2= 7.7…

A: Given

Q: Find Vout

A: In this case, the output voltage of the following circuit is to be determined:

Q: 24 Determine the current flowing through the resistor R1 if the Zener voltage is 3V. * D1 R1 5V 1K

A: The solution is given below

Q: solo: 120 72 36

A: to identify the branch currents for the circuit: R1 = 12 OHMS R2 = 72 OHMS R3 = 168 OHMS

Q: 4- What is Ohm's law of applications? 5- What are non-ohmic resistance? Give two examples.

A:

Q: Determine the total charge entering a terminal between t= 1s and t= 2s if the current passing the…

A: Current i = dq/dt Therefore charge Q = integration of current with respect to time. So integrate…

Q: What is the power required in an electrical circuit with a current of 2A and a resistance of 47…

A: NOTE: We are authorized to answer the first question since the exact one wasn’t specified. Please…

Q: Match the property of electric circuits with the variable- representation in an equation.

A: To solve any electric circuit problem, one should know about the basic rules of electric circuit,…

Q: A parallel combination consisting of resistors A and B is connected across the terminals of a…

A:

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.