Checking the height-thickness ratio of masonry members D. Examples 2. The longitudinal wall of a single-span house is the pilaster wall with the spacing of two adjacent pilasters equal to 4m. There is a window with the width of 1.8m between two pilasters and the height of pilaster is 5.5m. The house is taken as the rigid-elastic scheme. Check the height-thickness ratio of the pilaster wall (the grade of mortar is M2.5).

Checking the height-thickness ratio of masonry members D. Examples 2. The longitudinal wall of a single-span house is the pilaster wall with the spacing of two adjacent pilasters equal to 4m. There is a window with the width of 1.8m between two pilasters and the height of pilaster is 5.5m. The house is taken as the rigid-elastic scheme. Check the height-thickness ratio of the pilaster wall (the grade of mortar is M2.5).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please
SIT. D: A simply supported beam 250 mm wide, 500 mm deep and spans 6 m supports a service super imposed dead load of 10 kN/m and service live load of 6 kN/m. Concrete strength f' = 21 MPa and steel yield strength fy = 415 MPa. Concrete Icover to bar centroid is 70 mm. Determine the total factored load for ultimate strength design in kN/m. C. 23.45 10. 11. 12. A. 19.52 B. 25.20 D. 21.06 Determine the maximum ultimate moment in kN-m the beam must resist using load combination of NSCP 2015. A. 108.90 B. 131.58 C. 97.20 D. 113.40 Determine the required tensile steel ratio at ultimate stage. C. 0.007245 D. 0.009821 A. 0.007167 B. 0.013710
The standard acceptable 28-day compressive strength of grout for hollow unit masonry in MPa is? O a. 13.5 O b. 7.0 Oc 20.7 O d. 5,5 O e. 21.0
A standard brick (dimensions 8 in. x 4 in. x 2.5 in.) is compressed lengthwise by a force P, as shown in the figure. 8 in. 4 in. 2.5 in. If the ultimate shear stress for brick is 1,753 psi and the ultimate compressive stress is 4,300 psi, what force Pmax is required to break the brick? (Enter the magnitude in Ib.) Ib
here are the answer, only need solutions 1.f = 11.46 MPa 2.Mcr= 88.90 kN-m 3.fconc= 17.14 MPa; fsteel= 318.20 MPa
A half-block concrete masonry unit is tested for compressive strength. Theoutside dimensions of the specimen are 190 mm X 190 mm X 190 mm.The cross section is a hollow square with a wall thickness of 25 mm. Theload is applied perpendicular to the hollow cross section and the maximum load is 225 kN.a. Determine the gross area compressive strength.b. Determine the net area compressive strength.
60. If the loss of prestress is excessive resulting in tensile cracks, which method should be used? A. O Preloading method B. O Hollow method C. O Transparent method D. O Layered method
these are the answers I only need solutions 1. f = 8.42 MPa 2. Mcr= 121.0 kN-m 3. fconc= 10.42 MPafsteel= 197.22 MPaf’steel= 104.30 MPa
The masonry pier is subjected to the F = 780 kN load. Consider x = 0.25 mm and y = 0.5 mm. Neglect the weight of the pier. Part A Determine the normal stress at corner A. Express your answer with the appropriate units. Part B Determine the normal stress at corner B. Express your answer with the appropriate units. Part C Determine the normal stress at corner C. Express your answer with the appropriate units.
Now there is a roof beam, its height h=500mm, span L=4m, beam support length is 240mm, the wall thickness t=240mm, the design value of masonry compressive strength f=1.5 MPa, then the question is what is the eccentricity e of the wall top section under the roof beam?
Use fr ( Modulus of Rupture) = 0·7√ f'c a = 500mm b = 200 mm f'c = 21 mpa C = 150mm d = 500mm e = 150mm Concrete density (normal) = 24 kn/m² a) Determine the gross moment of Inertia, in x10 mm" b.) Determine the cracking moment, in kN.m c.) betermine the live load that the beaum can carry if it has a simple span of 10 meters in KN.m. b —a—