4G3G0 MID 202102.jp...Petermine the Diame ter of galvanized pipeQ4to discharge 6 m/hr with a headlength of pipe somrequiredLoss 2om and withは2=115水6?(2-2)

Discharge (Q) = 6m3/hr =1.66667 * 10-3 m3/s Length of the pipe (L) = 50m Head loss (h) = 20m…

Answered: ce) Determine the Diame terof…

ce) Determine the Diame terof galvanized pipe required to discharge 6 m/hr with a head Loss 2om and with a length of pipe som

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Why is motor impeller rotation so critical for 3-phase centrifugal pumps? Select the best answer…

A: This question is related to Pumps from Hydraulic Engineering from Civil Engineering.This is multiple…

Q: A fire pump delivers water through a 150 mm main to a hydrant to which is connected a 75 mm hose,…

A: Given, P1 = 550 kPa ∆Z = 10 m

Q: I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala…

A: The static Indeterminacy of structure= 0, hence ILD of this structure will contain only straight…

Q: _n-coil with a temperature of 6°C and leaves it -pipes system shown in the figure below.

A: Given:- temperature=6 degree celcius change temperature=12 degree celcius To find:- diameter of all…

Q: A series RL circuit with R = 41 2, and L = 9 H has a constant voltage E = 105 V applied at t = 0 by…

A: Consider the given data R=41 ΩL=9 HE=105 Vat t<0, Inductor is fully dischargedSo current…

Q: 0. In a building, to provide ultimate comfort to occupants can be used.

A: This question is related to Building Design from civil engineering.

Q: 20 H.W.9// For the closed tank with Bourdon-tube gauges tapped into it, what is the specific gravity…

A: Given:- The pressure reading on gage A (PA) = 50.0 kPa The pressure reading on gage A (PB) = 58.5…

Q: A fire pump delivers water through 15cm main pipe to a hydrant to which is connected an 8cm hose,…

Q: A single way valve that lets air into the pneumatic system. but doesn't allow the air to return back…

A: Cheak valve - Cheak valve are used to control back flow of water they are used to flow only in one…

Q: 30kN to 2m B 10KN/m A C 10m R1 R2

A: Introduction : A bending moment is the reaction that occurs in a structural element when it is…

Q: O1 A rectangular channel 2.5 m wide has a specific energy of 1.5 m when carrying a discharge of 6.48…

A: To find the alternate depth and critical specific energy-

Q: Given The figure shows a pump delivering 700 L/min of oil (sg - 0.8a) from an underground storage…

Q: remove impurity from wastewater. Calculate effluent B.O.D of a two stage trickling filter with…

Q: particular load runs at 24rev/s when drawing 15A from the supply. Calculate the speed of the motor…

A: Armature resistance, Ra = 0.2 ohm Field resistance, Rf = 0.3 ohm Supply, V= 240 V Current, I is…

Q: B-74C A piping system involves two pipes of different iameters (but of identical length, material,…

A: This question is related to the Pipe flow from fluid mechanics from Civil Engineering. In this…

Q: If the coef. of discharge of the Venturi meter in Fig. 8-50 is 0.92, determine the actual discharge…

Q: 6. A galvanized iron pipe is required to carry water at a discharge of 3.5 cfs and with a head loss…

Q: 15 cm main pipe to a hydrant to which is connected an 8 cm. hose, termination in a nozzle 2 cm in…

A: P1=550kPa P1=0 (atmospheric) D1=15cm D2=2cm

Q: Water from an open tank elevated 5m above ground is allowed to flow down to a pump. From the pump,…

A: Given, L = 100 m np = 55% Q = 0.8 m3/min or 0.0133 m3/s

Q: A tank filled with water at 30°C is supplies water for a shower based on gravity driven flow. The…

A: The given data is shown below: Temperature=300CDiameter=1.5 cmCoefficient of exit loss=0.5Flow…

Q: Consider a 98% efficient ESP which removes, fly ash from combustion gases flowing at 100 m3/sec. The…

A: Given Data,The resistivity of Ash = 1×1010 ohm-cmQ=100m3sη= 98% (Efficiency)1) Calculation of total…

Q: Q3) Determine the diameter of a galvanized iron pipe (e-0.07 mm) and the average velocity in the…

Q: 10-26 If a flow of 3 cfs of water is to be maintained, what power must be added to the water by the…

A: This question belongs to subject fluid mechanics. In this question find out power added to the water…

Q: Q3) In a long-shunt compund generator, the terminal voltage is 230 V, when it delivers 150 A. The…

Q: IX. PROBLEM SET NO.1 1. A closed tank contains 0.610m of mercury (sp.gr.-13.6), 1.524m of…

A: To Determine Reading of the gage in the top of the tank.

Q: Q2: For the system shown in figure below, find the power that the wrbine (1) can extract The…

Q: (1) Determination of meta-centric height of a boat model. (2) Determination of co-efficient of…

Q: A single-phase 111-V, 50-Hz supply is connected to a coil with 200 turns of a coil-core assembly as…

A: Given, Voltage RMS , E = 111 V Frequency (f) = 50 Hz Number of turns (N) = 200

Q: A WTP receives (15140 m³/day) of water. Five clarifleculators unit each of (12) m outside diameter…

Q: An ESP must treat 300,000 acfm with 99% efficiency. Estimate the cost of this ESP (f.o.b.…

A: Given- Q=300,000 acfm=5000 ft3/sn=99%=0.99

Q: A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a…

A: power is generally a measure of the rate at which work is done. In other words, it is operating…

Q: Determine the discharge and compute the power consumption. (Neglect all minor losses.) A Q eff PUMP…

A: D = 0.2 m f = 0.02 k = 10

Q: A water treatment plant is designed to treat a flow of 20,000 m³/day. The chlorine dosage is I mg/L.…

A: Flow, Q = 20000 m3/day Chlorine demand = 1 mg/day To determine Minimum size of the container…

Q: the fermissi ble distmce (^) if Che Eainspon is 4OMPa a llowable st Yesses in and comporsion is 80 M…

Q: A fire pump delivers water through a 15 cm main pipe to a hydrant to which is connected an 8 cm.…

A: P1=550kPa P1=0 (atmospheric) D1=15cm D2=2cm

Q: Converging-diverging nozzle is also known

A: To find : Another name of converging diverging nozzle.

Q: Cavitation and flashing are two different phenomena that should be avoided in the valve operation.…

A: Introduction- Cavitation and flashing are very common in valve operations. These two are different…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

4G
3G
0 MID 202102.jp...
Petermine the Diame ter of galvanized pipe
Q4
to discharge 6 m/hr with a head
length of pipe som
required
Loss 2om and with
は2=115水6?
(2-2)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Calculation

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

This condensing coil has 3 grill openings. The total length of the openings is57 inches. Find the length of the center opening.
8) A 5.9866 cm-diameter water jet with V-45 m/s, strikes a moving blade with Vb-15 m/s. The power generated is ----- (a) 76 kW (b) 760 kW (c) 760 W (d) None of these.
Subject: Fluid mechanic Provide complete solution.
Urgent
A piping transport system uses a standard 1.25-in S40 pipe with 26 standard ells, 19 tees (standard), 11 tees (as ell, entering branch) and 16 gate valves (open). What is the actual power requirement (in hp) to transport a liquid with viscosity of 1.91 cP and a specific gravity of 0.8137 is transported through 2212 ft of this piping system? Assume that the flow of liquid is at 33.1 gpm and the discharge is 42 ft above the inlet having a gauge pressure of 11.2 psig. The pump is assumed to be 45.7% efficient and liquid is transported from a large reservoir at 14.7 psia. Answer options: 44.4 7.55 10.3 30.7 29.4
G/E is Select the correct response: 3(1-2v) 0.33(1-2v) 2(1+v) 0.5(1+v)
Problem-5 c, A single-phase fully controlled thyristor bridge ac-dc converter is operating at a firing angle of 25° and an overlap angle of 10° with constant dc output current of 20 A. T Find the fundamental power factor (displacement factor) at input ac mains of 230 Vrms.
Please explain all parts
A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KP.. Compute the power in that point of the pipe. Hide answer choices a A) 13.37 HP B) 14.99 HP 8.87 HP D) 11.19 HP E No Answer among the choices O O O
A liquid of specific gravity 1.7 flows in a 60-millimeter horizontal pipe. The total energy at a certain puint in the flow is 75 joules per newton. The elevation of the pipe above a fixed datum is 2.5 meters. If the pressure at the specified point 70 KPa. Determine the following: a. velocity flow b. discharge c. power available at the specified point in watts.
The Best Efficiency Point is the point in a pump curve that coincides with its maximum flow rate. True False
Q1/ liquid is pumped from a ground 90 elbow 90° For this system: - (Le/d) of globe valve = 240 (Le/d) of 90" elbow = 40 (Le/d) of 45" elbow - 18 h: of Heat Exchanger 1 = 2.2 m of liq. Fof Heat Exchanger 2 = 25 J/kg Pump efficiency elbow level reservoir to an overhead tank H.Ex.2 through a 15 cm ID pipes of e/d = 0.018 as shown in figure: i. What is the pressure developed by the pump to supply water to Tank Globe Valve 45" elbow - 62 % Pump the tank at the rate of 960 45° elbow /min? ii. What is the power required for the pump? Given that: u = 1.6 cP; sp.gr 0.86; and the lengths as follow; L = 33 m, L2 = 17 m, L3 = 8 m, L4 = 35 m Reservair H.Ex.1