CCode V Consider the following Convolutional code encoder, where the initial value of all memory registers is zero. Which of the following is the correct sequence of states (S1, S2) after you feed it in the input 111? Note, for (ab) --> (cd) --> (ef), the state (ab)=(S1, S2) is the state after the first bit is fed into the encoder, and (cd)=(S1,S2) corresponds to the state after the second bit is fed into the encoder and so forth. I Select one: O a. (10)-> (11) --> (11) O b. (10)-> (01) --> (11) O c. (00)-> (01) --> (11) O d. (10)-> (11) --> (00) O e. (00)-> (11) --> (11) S₁ X S₂ Y

CCode V Consider the following Convolutional code encoder, where the initial value of all memory registers is zero. Which of the following is the correct sequence of states (S1, S2) after you feed it in the input 111? Note, for (ab) --> (cd) --> (ef), the state (ab)=(S1, S2) is the state after the first bit is fed into the encoder, and (cd)=(S1,S2) corresponds to the state after the second bit is fed into the encoder and so forth. I Select one: O a. (10)-> (11) --> (11) O b. (10)-> (01) --> (11) O c. (00)-> (01) --> (11) O d. (10)-> (11) --> (00) O e. (00)-> (11) --> (11) S₁ X S₂ Y

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

i need the answer quickly
Let x be an 8-bit unsigned number. What is the value of x in base 2 for which the following instruction clears the bits 2 and 4 of GPIOC- >PDOR without modifying any other bits? Do not write the Ob prefix! GPIOC->PCOR = x;
Transcribed Image Text (Micro processer 8086) Q1) Choose the correct answer: 1. One of the following instructions is correct: a. MUL 67 b. LEA BL.[SI] (2. AS) c. LALF d. Neither a,b nor c 2. Suppose we have SS starts at B4102 H, CS ends at E4250H. The suitable point for DS to start so there are no overlapping of the segments is: c. C4200 H d. C4300 H a. C4000 H b. C4100 H 3. If you have AX-0208H, BL=D8H, the results of performing IDIV BL in AX is: a. 00F3 H b. F300 H c. 5802 H d. 0258 H 4. The Execution Unit includes: a. Instruction pointer b. Status register c. Address generation d. Neither a,b nor c 5. The compare instruction and test instruction are similar in : a. Both instructions are subtraction methods b. Both instructions effect on ZF, SF & PF. c. Both instructions store the result in the destination operand d. Neithe a,b nor c 6. The data bus in 8088 Mp is: a. 16-bit unidirectional lines c. 8-bit unidirectional lines b. 16-bit bidirectional lines d. 8-bit bidirectional…
Translate the following MIPS code to C. Assume that the variables f, g, h, i, and jare assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the baseaddress of the arrays A and B are in registers $s6 and $s7, respectively and that A and B are arrays of words. addi $t0, $s6, 4lw $t0, 0($t0)add $t0, $t0, $t0sw $t0, 0($s6)
By assuming that X = 3, and 33 is a two digit number, consider memory storage of a 64-bit word stored at memory word 33 in a byte-addressable memory (a) What is the byte address of memory word 33? (b) What are the byte addresses that memory word 33 spans? (c) Draw the number 0xF1234567890ABCDE stored at word 33 in both big endian and little-endian machines. Clearly label the byte address corresponding to each data byte value.
This is Machine Architecture! ***WRITE THE CODE ON YOUR OWN*** Create a MIPS program that demonstrates that the associative law fails in addition for floating point numbers (single or double precision). You only need to demonstrate it for single precision. Remember the associative law is a + (b + c) = (a + b) + c. The program’s output should look something like the following where the xxx’s are the numbers you chose. The resulting numbers may be different than mine depending on your choice of a, b, and c. Using a = xxx, b = xxx, and c = xxx a + (b + c) = 0 (a + b) + c = 1 The key is to have two of the number large (one positively and one negatively but equal in magnitude) floating point numbers and the third floating point number very small in comparison. As a side note, the associative law will also fail for multiplication for floating point numbers, but you do not need to demonstrate that. Please don't forget to include comments in this code
Can you please explain each step as to how to read and list out each step of what values are in each registers each step of the way to get to the final result? Please see attached.
please give a step by step implementation of this using only operators in the nand2tetris hack assembly language
Please give me the correct answer only. Don't copy from others
You need to write in hexadecimal (E.g: OX00114A63) for the following RISC-V assembly instruction: sub ra,gp,t1 * WARNING: You MUST write the Ox followed by the 8 hexadecimal digits all in UPPER case. If needed, add extra zeroes to have the 8 digits (this is auto graded, so no spaces, underscores or lower case). In the previous hexadecimal example Ox00114a63 is incorrect, OX114A63 is also incorrect, and 00114A63 is also incorrect. Only OX00114A63 is correct.
how how the word “RISC-V2v” coded in 8-bit ascii code would be arranged in the memory of a littleendian and a big-endian machine respectively. Assume that the machines are byte-addressable and the data are stored starting at address 0x00000000. You can use the hex representation instead of binary
Answer using the assembly language.