Create Section AA' and BB'

Q: which is given. What are the x and : coordinates of the bracket's mass cen- ter? (The angle 0 in the…

A: To Find :  The x and z coordinate of the bracket mass . Given :  The total number of hole is n=4 The…

Q: 6" 2" 4" 3" - x K4"→ 6" Using the figure above, calculate the following 1. Total area of the figure,…

A: GIVEN DATA AN AREA IS GIVEN COMPOSED OF TRAPEZOIDAL WITH CIRCLE WE HAVE TO CALCULATE ALL THREE-POINT…

Q: Nut 17.0 N 37° 25.0 cm

A: The text provides the following information:The force applied to the wrench is 17.0 NThe distance…

Q: Consider the cable system shown in FIGURE P3-18 of the textbook. If: • e - 45° then, what is the…

A:

Q: Q/ For the figure shown below, compute the centroid of the figure. 3m 3m 4.5m 6m

A:

Q: Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial…

A:

Q: Draw the three views and a section elevation: 12 15 12 4 HOLES, DIA 16 40 0G 12 20

A: given view  side and front view  to sketch the top view

Q: Determine the centroid coordinates (X , ỹ) for the beam section shown in Figure Q6. a) Give your…

A: ( x , y ) = ( 24.375 mm , 41.875 mm )

Q: A 3 m- B- 4 kN/m

A:

Q: The engine of car has six cylinders of 82.55mm bore and 769.5mm stroke. The compression ratio is…

A:

Q: The magnitude of the vertical force W is 160 N. The direction cosines of the position vector from A…

A:

Q: The cross section of the rim of an iron flywheel 3 ft. In diameter is a rectangle 12" by 2". How…

A: A flywheel is a spinning device that is designed to efficiently store rotational energy by using…

Q: 500 Delermine He moment a bout Point e(o) as Shown

A: It is required to determine moment about point O

Q: Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

A:

Q: A cone, base diameter 65 mm and axis 75 mm, is lying on the ground on one of itsgenerators with the…

A: Sectional view of the cone is shown.

Q: A belt drive consists of pulleys of one pulley of diameter 667 mm and another pulley of diameter 321…

A: Given data,  D=667 mm  d= 321 mm  Cross belt arrangement  Center distance arrangement x= 2.6 m…

Q: The lower half of the moulding box is O a. Raiser O b. Drag O . Runner O d. cope

A: Given data Lower half of the moulding box is

Q: 6 m

A:

Q: calculate the hydraulic diameter of a two long flat plates with the measurement of 5 inches distance…

A:

Q: The rectangular lamina with breadth = 60 mm, depth = 30 mm. The Ixx value is mm4 Select one: 540 x…

A: Dimensions of rectangle lamina b=60 mmd=30 mmIxx=112b×d3

Q: The point of contraflexure is a point where a. Shear force changes sign b. Shear force is maximum c.…

A: A point of contra flexure is a point in the bending moment diagram where the bending moment is zero…

Q: 2. Find the centroid of the figure shown. "20 in 18 in 10 in 12 in

A:

Q: A.7 Compute I, for the shaded area given that = 25.86 mm.

A:

Q: ompute the moment of inertia, Ix of the crosS-sectional area about the neutral axis. + 6 in.- 6 in.…

A:

Q: Write the equation of the Centroid of an area?

A: The centroid of an area is the center of gravity of that particular area where the entire mass can…

Q: A. Which of the following gives the area in square meters. B. Which of the following gives the x…

A:

Q: Find the resultant and angle of direction based on the horizontal. using tail to tip method 1. 20…

A:

Q: Find the volume of a right circular cylinder of radius a and height h if the density varies as the…

A: Given    Radius = r    Height = h Find   The volume of a right circular cylinder

Q: A 5 ft DU B 5 ft -3 ft-

A:

Q: Deive equabon for height Rof Pate Governer useig Instantenous Centre Method.

A:

Q: Construct the third projection of the cylinder.

A: According to the details provided in the question, we need to find three views.

Q: 500 I In the fig. shown, compute the ff: (16-18) the resultant using cosine law (force polygon) 60 R…

A: Solution:   According to the Cosine law, the Resultant of two concurrent, co-planar force system…

Q: Find the resultant and angle of direction based on the horizontal. using tail to tip method 1. 43…

A: According to the details provided in the question, we need to calculate RESULTANT AND ANGLE

Q: Please no written by hand solutions Diagonals FR and ( E)/( m)eet at D,bar (DE) is 8cm and bar (FK)…

A: Given: The length of bar DE is 13 cm and the bar FK is 13 cm.

Q: 3.44 The landing gear of an airplane can be idealized as the spring-mass-damper system shown in Fig.…

A:

Types of Foundation