Calculate the voltage gain of the following circuit. Assume that the capacitors are very large and A = 0. Şekilde gösterilen devrenin gerilim kazancını hesaplayınız. Kapasitelerin çok büyük olduğunu ve A = 0 kabul ediniz. Circuit parameters / Devre Parametreleri Rsig = 8 kQ, RG = 27 kQ, Rs = 300 N, RL = 5 kN, gm = 0,05 S VDD RG R sig M1 C2 oVout sig Rs RL O a. 0.76

Calculate the voltage gain of the following circuit. Assume that the capacitors are very large and A = 0. Şekilde gösterilen devrenin gerilim kazancını hesaplayınız. Kapasitelerin çok büyük olduğunu ve A = 0 kabul ediniz. Circuit parameters / Devre Parametreleri Rsig = 8 kQ, RG = 27 kQ, Rs = 300 N, RL = 5 kN, gm = 0,05 S VDD RG R sig M1 C2 oVout sig Rs RL O a. 0.76

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
List the five capacitor replacement rules.
Vcc = +12 V %3D a. Determine the following values for the fixed-bias configuration in the figure to the right. Rc IBo and ICO 2.2 k2 C2 RB 240 k2 ac output VCEQ, VB, and Vc 10 uF C ac input VCE B = 50 VBC 10 µF
Calibri (Body) -11 by AaBbCcDx AaBbCcD AaBbC AaBbCc AaB AaBbCc. mat Painter BIU 1Normal 1No Spaci. Heading 1 Heading 2 Title Subtitle Chang Styles d Font Paragraph Styles IMPEDANCE QUIZ # 2 1. What capacitance when connected in series with a 500Q resistor will limit the current drawn from a 48-mV 465-kHz source to 20µA? * a. 144pF b. 145pF c. 146pF d. 147pF MY ANSWER: c.146pF 2. What is the total impedance at 20kHz of a series circuit consisting of a 1.5mH inductance, a 100Q resistance, and a 0.08uF capacitance? * a. 1340 41.7 b. 1930 L-37.2" C. 920 290 d. 530 2-12.6°
A step down converter is operated with a duty cycle of k 0.75. The input voltage is V, 20V. and the load is L=5mH, R=152 The minimum inductor current is I 0.1A. The maximum inductor current is %3D %3D Select one: O a. 0.9 A O b. 1.9 A O C. None of these O d. 1.1 A O e.2A
Solve for Rc of Figure 42. 12 V Ic Rc RB VCE B=80 IB = 40 μA Reference: Boylestad, R. & Nashehky, L. (2013). Bectronic devices and circuit theory |11th ed.]. Upper Saddle River, New Jersey: Pearson Education Figure 42 1.5 k ohms 1.875 kohms 3.531 kohms 2.75 kohms Vc=6V
In the circuit given below, what should be the minimum value of C1 capacitor so that this capacitor does not affect the circuit negatively when f = 797 Hz? (Aşağıda verilen devrede f = 797 Hz iken, C1 kondansatörünün devreyi olumsuz etkilememesi için bu kondansatörün minimum değeri ne olmalıdır?) V1 Cbp 0.1pF R2 12V 33K R4 100K C1 R3 Vin U1 C2 Vout 4.7K V2 LM358 R1 SINE(O 50mV) 33K
Convert the circuit from a T to a pi configuration
* Super Position 12A 6V Si talke S.
When charging and discharging of a capacitor, the capacitor voltage vs time curve will be O Linear O Constant O Exponential O Square
Question 4 A boost converter has an input of 5V and an output of 20W at 15V. The minimum inductor current must be no less than 50% of the average. The output voltage ripple must be less than 1%. The switching frequency is 30kHz. Determine the duty ratio, minimum inductor value, and minimum capacitor value. Verify your answers using Matlab, show the inductor current is continues and its minimum is no less than 50% of its average. Furthermore, the output voltage ripple is less than 1%.