calculate the strength of the rod S2.

Q: A) Draw the free body diagram of Joint C. B) Use the joint method to solve for the forces in truss…

A:

Q: The figure above is a truss supporting the deck of a bridge. a) determine the support reactions.…

A:

Q: W 30 A.

A: given:

Q: A frame of two members (AC) and (BD) are connected together at pin B. The other ends are pin-…

A: According to the information we have a frame with two members AC and BD that is pinned together at…

Q: Q) Consider a weight supported by a cable as shown in figure below is equal 100 kN. Determine the…

A:

Q: M D B- L+- +- 1.5L 1.5L-1.5L - 0.5L 0.5L A frame consists of two members, AD and DBC that are…

A: Draw the free body diagram for the above problem.

Q: 2) Find the true magnitude and direction of the forces in all the members of the truss AB AND AC at…

A: Solution:

Q: 1. Figure Q1 shows an illustration of a bell crank mechanism that is in a state of static…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Write and explain all calculations involved. ps/ Please write it with simple handwriting so i can…

A:

Q: A D α C W

A: GivenW=34kNθ=60oL1=2.6mL2=2.6m

Q: 275 mm 30 30° E 0.5m FHE A) d=0.275 500 mm C D 0:5m 500 mm B) d=0.5 300 mm C) d=0.5*cos30 friction…

A: If a force F is inclined at an angle θ with the horizontal, then the component of force along the…

Q: F=2580 Ib 4 5 A 28 ft

A: Draw the free-body diagram of the beam, Resolve the Force F=2580 lb into two components,…

Q: A steel rod is acted upon by the loading shown below. 50 mm² is the area of the circular rod. The…

A: Hi, I have calculated the asked using the superposition principle. You only have to find the force…

Q: 1) Find the true magnitude and direction of the forces at the supports A and B in the case of static…

A: Static Equilibrium: A body is said to be in static equilibrium if it satisfies the following…

Q: The axle radius is 1 m and the wheel radius is 4 m.  A 1600-N load is attached to the axle via a…

A: To maintain static equilibrium, the following three equations must be satisfied: 1. The summation of…

Q: E 2m + 2m + 2m 1.5m B D 2m A 2 kN 2 kN 2 kN 1) a) Determine the force in members CE, BD, and CD and…

A: Given: The diameter of the pin at A and G, d = 2 cm = 0.02 m

Q: 7. Find the centre of the figure below so that it is in equilibrium. m2 A MIF2 5 N a) 10N 2m X 10x…

A: A-B-To determine:The center of both the figures

Q: 2. A truss is shown in the figure below. a) Based on the number of joints and members, discuss about…

A:

Q: Given the Frame as shown below. Using Method of Members, determine the following if the External…

A:

Q: Figure 2 shows the beam is loaded by distributed loading and supported by the cables DB and DC as…

A: Given: The intensity of udl, w = 800 N/m

Q: 6/2 The 700-N force is applied to the 100-kg block, which is stationary before the force is applied.…

A: Draw the free body diagram for the block. Here, W is the weight of the block, F is the frictional…

Q: The system given in the figure is in balance with the help of the wire in the middle, which is…

A:

Q: 1 m 1m- 1 m 500 N C 1 m В

A:

Q: What would be the maximum weight W of the block, shown in the following figure, so that the tension…

A: The free-body diagram of the hanging weight at point C is drawn below. Here, T represent the…

Q: . Examine the equilibrium configuration for the beam shown below. Assume the beam and support are…

A:

Q: RSL-2 A rod of negligible mass is pulled down at each end as shown to the right. The rod is…

A:

Q: Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces in each member…

A: Given: Find:a The magnitude and direction of the reactions at 3 and 5b The forces in each member of…

Q: For the picture below, choose the correct free body diagram. 15m AN 800N 600N Im Im A Fac Nono A 2m…

A: Introduction Free-body diagrams are used to depict the magnitude and direction of all forces…

Q: Given: Find: A 0.5-inch diameter pole (L1-12 in, L2= 22 in) is loaded with three forces (two forces…

A: Pole diameter, D = 0.5 inch  L1 = 12 in, L2 = 22 in  P1 = 2.5 kip or 2500 lbs  P2 = 7 kip or 7000…

Q: TRUSS PROBLEM Determine: a) The magnitude and direction of the reactions at 3 and 5 b) The forces…

A: To find - a) The magnitude and direction of the reactions at 3 and 5. b) The forces in each member…

Q: a) Determine whether the structure is statically determinate. b) Calculate the support reactions. c)…

A:

Q: A) Draw a Free Body Diagram of the whole frame, being careful about how you handle the rope. The…

A:

Q: Determine the magnitude of the pin reaction at A in kN. b) Determine the magnitude of the pin…

A: Given: To determine: The pin reaction at A  The pin reaction at B  The pin reaction at C

Q: Q4) Structural Analysis This bridge is made of two-force members attached at the ends. All angles…

A:

Q: 4- For this truss e=60°, a) Determine the type of supports b) Reaction forces at each support c)…

A: Dear student,                     According to the expert guidelines, I am allowed to answer only…

Q: A C B D 6 m 3 m 3 ni

A:

Q: equilibrium. It is constructed using two-force members, joined at their ends.  I have given you all…

A:

Q: The sculpture is attached to the wall from a metal rod at A which is a fixed support. The sculpture…

A:

Q: D b C a 60° |A B A) Draw a Free Body Diagram of the post BCD. B) Compute the force at point C. a =…

A:

Q: 4 in- 4 in- 20 lb 40 lb B 2 in. 3 in. 3 in. E 1. The bracket is supported by pegs at C and D and a…

A: Solution; let the equivalent force acting at x distance from point A.  60×x=40×8x=326=163in

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.