Calculate the minimum coefficient of static friction for each contact location to prevent the pole to slide down. Assume the two contacts have equal coefficients of friction. -The uniform 7-m pole has a mass of 1pq kg and is supported as shown below. 7 m 3 m 4 m

Calculate the minimum coefficient of static friction for each contact location to prevent the pole to slide down. Assume the two contacts have equal coefficients of friction. -The uniform 7-m pole has a mass of 1pq kg and is supported as shown below. 7 m 3 m 4 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Which spring, the truncated cone spring or the helical spring, would have a larger spring constant? Explain.
A light balloon that has a volume 2.50 m³ filled with a helium (pne = 0.179 kg/m*) is tied to a light string of length L = 5.50 m. The string is tied to the ground, forming an "inverted" simple pendulum, as in Figure 2a. If the balloon is displaced slightly from the equilibrium position, as in Figure 2b (Pair = 1.29 kg/m³). Determine a) the spring constant, k, (Hint : Use an analogy with the mass hanging at the end of a spring. Solve for the value of k assuming that the restoring force acting on the system takes the same form as Hooke's law), b) the time period of its simple harmonic motion c) the frequency of the simple harmonic motion. He Не Air Air Figure 2: Inverted Pendulum for Question 5
A shaft is rotating as part of an aircraft compressor. A disc is located midwayalong the rigid shaft that is L=1.8m long in total as shown in Fig. Q4. The discalso lies midway between two supporting bearings that are LB=1.4m apart. Thedisc has a mass of MB=100kg and the centre of mass of the disc is locatedrB=12mm from the axis of the shaft. A mass is added at each end of the shaft.The first has mass MA=40kg and eccentricity rA=37.5mm, whilst the second hasmass MC=30kg and eccentricity rC=40mm. If the system is in static balance:(a) Group the required information in an appropriate table and construct theforce polygon of the rotating system. (b) Determine the angles A and C which ensure the shaft is in staticbalance.(c) Construct the moment polygon for the rotating system and determine the out-of-balance moment when the shaft rotates at ω=100rev/min.
· 20 lb 30 a (2 in A ما 25 B 6 in 12 in 450 D E LOA of F₂ 6 in 30 lb Three forces act on a truncated square plate at A, B, and E, as shown. Find an equivalent system consisting of: a horizontal force, F₁, at D force, E₂, at e, whose LOA is at 45°° to the horizontal LOA of F • a couple of moment M. Be sure to specify both mag and sense for I and I₂, and also both mag and sense (cow or CW) for M.
1. establish maxwell's relations for calorific capacities and explain what you mean in terms of state variables
Two forces were acting together on a certain point (point e) in a mechanical system; force L and force M. The magnitude of force L is (0.2 N), and on a 2D plane force L is directed from point (–2, –3) to (0,1). The magnitude of force M is (0.5 N), and on a 2D plane force M is directed from point (–4, 2 ) to (2, 2). Solve the following: a) Find the unit vectors of both force L and force M, represent them in terms of the unit vectors î and ſ. b) Find the vector representations of force L and force M in terms of the unit vectors î, and ĵ. c) Find the vector representation of the resultant force acting on point e, represent the net force using the unit vectors î, and ĵ. d) Determine the work done by the resultant force, F, in moving an object through a displacement r=1 î+2ĵm. Show your full analytical solution to all parts.
A gas vessel 1.5m x 1.5m x 2m containing Carbon Dioxide (CO2) with a temperature of -3°C. The right vessel wall is fixed to the wall, as shown in Figure Q1 (a). A minimum force of 10kN is required to split/open the gas vessel. Calculate: i. Vacuum pressure of CO2.ii. Mass of the CO2. Take molecular weight for Oxygen= 16, Carbon = 12, atmosphericpressure 100kPa, and universal gas constant = 8314 J⋅kmol−1⋅K−1
Please find the question attached.
4
Do this in paper, plz
Q3: A wire 10m long of cross section area 1.22 cm? olongates by 1.5 cm when 4.5 kg is suspended from it find: 1. Stress 2. Strain 3. Youngs modulus of the wire
Q3: In a mechanical application a composite part is required to have the properties, the longitudinal modulus of elasticity is at least 105 GPA, the transverse modulus of elasticity is at least 5.62 GPa, and the density is no more than 1400 kg/m³. The available fibers have the properties: the longitudinal modulus of elasticity En=230 GPa, the transverse modulus of elasticity Ep=22 GPa and the density Pr=1800 kg/m³. And the available matrix properties are, the modulus of elasticity Em Em₂ = 3.5 GPa and the density pm - 1200 kg/m³. Does this composite can be fabricated from these fibers and matrix?