Calculate the minimum and maximum output voltage for the regulator. The minimum voltage is found by assuming the VBASE(02) is 5.7 V with a Zener drop of +0.7 V. This voltage is dropped across R4 and Rs. Since R3, R4, and Rs are in series, the output can be found by the proportion: VOUT (min) VBASE(Q2) = R3 + R4 + R5 R4 + Rs

Calculate the minimum and maximum output voltage for the regulator. The minimum voltage is found by assuming the VBASE(02) is 5.7 V with a Zener drop of +0.7 V. This voltage is dropped across R4 and Rs. Since R3, R4, and Rs are in series, the output can be found by the proportion: VOUT (min) VBASE(Q2) = R3 + R4 + R5 R4 + Rs

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A clamper circuit has 20 Vp-p. 100Hz square wave input voltage. The circuit consists of silicon diode IN4001 and 3V battery as shown in Figure 1 C. 0.1 µF D R Vi(t) 50 k2 Vo(t) 3 V Figure 1 a) Find the output voltage for all input voltages values. b) Sketch the output waveform, Vo(t).
Question 3 Consider the following cirucit: in + V1 R1 5 PULSE (0 2 1 1 1 1) (Note again the unrealistic diode characteristics.) The input is a ramp: 2.0V- 1.6V- 1.2V- 0.8V- 0.4V- 0.0V- 0.0s 0.2s 0.4s 0.6s 0.8s out .tran 2 .model diode D(Ron=5 Vfwd=1 Roff=1G) V(in) D1 diode 1.0s 1.2s 1.4s 1.6s 1.8s 2.0s The output voltage is similar to the input voltage, except that it breaks at a certain voltage and reaches a different final value. Find the break voltage and the final value of the output.
1 (a). In the given waveform shown. Find the ripple factory, if V1 = 8 and V2 - 16. V(Volts)| V2 E- V1 t(seconds) 1 (b) Draw the circuit diagram for Full Wave Bridge rectifier with a capacitor filter.
ier quesuon Will save this response. Quèstion 6 Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to iL-DC =05A RL VLDC =20V 220V omsb 0.01 F 0.02 F 0.0167 F Hows b None of the above DEV Chp
Q/A Full-wave bridge rectifier with (400 Sin (1007) () ૧૦૯ Sinusoidal input has load resistor of (loks2). Sketch Vo and determine the i- 3 pa PIV
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
An FWR using a centre-tapped Transformer Supplies an average voltage of 120V to a 250 kΩ load Calculate (a) the peak value of output voltage (b) The required Transformer secondary voltage (rms value) (c) Average Current delivered to load (d) Average current through each of the diodes. (e) Peak Current through each of the diodes (f) PIV requirements for each of the diodes. AC supply voltage is 230V and assume ideal diodes.
1. The applied voltage in a Germanium diode is found to be 0.41 V with a threshold voltage of 26 mV and saturation current of 1 nA Calculate for the diode current. 2.The voltage as the switch is closed for an SCR circuit is found to be 4V and the current is 0.2A Compute for the average power conduction loss for a frequency of 60 H2 Assume the tum on and turn off time is 0.12 m and 0.25 ms respectively 3.If the trigger voltage in the circuit is replaced by SV, the series resistor by 330 ohms, compute for the gate current at the SCR when Switch 1 and 2 are momentarily switched on. The voltage at the gate to cathode is 0.7V while that of the voltage from anode to cathode is 10V 4.Id=11.84 mA n=2, and the applied bias voltage is 0.5V and the temperature requirement is at 20°C. Findthe diode saturation current 5.For a frequency of 60 Hz, compute for the average power conduction loss if the difference in the turn off and turn on time is 10 ms and the instantaneon power is given as a…
FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…
Find the average value of the full- wave rectifier if Vpeak = 20V %3D O a. 14.14V O b. 7.07V C. 12.73V O d. 6.36V
The average output voltage for a single phase half wave rectifier for the input sine wave of 200sin100 nt Volts is calculated as a. 63.661V b. 57.456V c. 75.235V d. 60.548V