Calculate the lattice constant of the alloy you found in part (a). Assume the alloy and its end members have the zinc blende structure and use azns = 5.409 Å and aznse = 5.668 Å.

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: solve and show every step with right answer

A: Data given - Rectangular cross section 225×75 mm2 Torsional moment = 20kN Axial Compressive force =…

Q: bäi The command using to insert :seal is

A: The Incident Command System is a standardized approach to the command, control, and coordination…

Q: please solve the  equations in steps ()i and ()ii

A:

Q: solution incorrect resolve again

A:

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: Draw the lines and find IC point for Link BD, if the angular velocity of ED 29 rad / s CCW, then…

A: GivenωDE=29rad/s ccw

Q: A steam engine 18° x 24" runs at 250 rpm.

A:

Q: S) t) What is the distance, d3x, of shape 3's centroid from axis Xo? What is the distance, d6x, of…

A:

Q: A horizontal beam AB supported by an inclined strut CD carries a load P. The strut, which consists…

A: Given data: Diameter of bolt at 'C' joint, db=0.62 in. So, area of bolt against shear is,…

Q: ove that the calculated values ne graphical method and the ematical analysis method the same, for…

A:

Q: of the table) and free to move if a force is applied. A force is applied on it as the arrow…

A:

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A:

Q: solve parts 4 and 5 please

A: To draw Mohr circle and to show the orientation of the element of maximum in plane shear stress

Q: Homework 2: It was found in a cylindrical turning of a circular shaft with a diameter of 24 mm that…

A:

Q: need answer in 15 minute's please 3 (29// A ruck is throw up according to equation s(t) = { +2E-6t…

A:

Q: I. GENERAL INSTRUCTIONS : Show complete formulas, solutions, and figures. Round off to 3 decimal…

A:

Q: Find Ixx for the given Plane, where b1 =160m, d1=25m, b2=20m, d2=90m, b3=60m & d3=25 m (Enter only…

A: Given data:-b1=160m, d1=25m, b2=20m, d2=90m, b3=60m, d3=25mArea of section 1, A1=160×25=4000m2Area…

Q: What is its minimum width if it produces 1000 minima?

A: The expression for the dept of the slits is given by the expression, Dsinθ=mλ For the minimum width…

Q: A 5” diameter short shaft carrying two pulleys close to the bearings transmits how much horsepower…

A: Given: d = 5"  N = 300 rpm

Q: Determine the forces inmembers DEBkd and ck of the Pin- connected Fruge. foon 6 *E Sol Гово foo Det…

A:

Q: oy. Suppose the vessel is subjected to uniform intemal pressure p, determine the minimum thickness…

A:

Q: Direction: Solve the following problems completely. Include all FBD with proper labels. 4 decimal…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on both…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: can u pls solve the question using hand written notes in detail and figure

A:

Q: between centers carry pulleys 4 feet and 3 feet in diameter respectively, connected by a crossed…

A:

Q: Calculate the mechanical advantage of the following compound machine.

A:

Q: An exponent, such as the 4 in the expression 94, means: the number of times the number before the…

A: It is required to determine value of 94

Q: A Tyrannosaurus named Rex was having a birthday. He was standing on one end of a cart that rolled…

A:

Q: Gentlemen, please help to solve a,b,c as I faced confusing questions about screw jack. Conditions…

A: Given: The load to be lift, M = 3.2 ton = 3200 kg The screw pitch, d = 12 mm The diameter of screw…

Q: The answers should not be in vector form. Please re-anser. Rate will be given

A:

Q: According to principle of moments * a. if a system of coplanar forces is in equilibrium, then their…

A: (1) According to principal of moments, moment of any force about any point is equal to the algebraic…

Q: sketch a rube goldberg machine using the following operations dominoes falling, rolling ball, pulley…

A: A rube goldberg machine is to be drawn considering the operations such as falling, rolling ball,…

Q: hello did you forgot the T in solving Wrev?

A:

Q: Part II. Longer problem focused on problem solving multiple steps. This problem will be graded based…

A: Step 1: Step 2: Step 3:don't forget to upvote :) thank you and comment if doubt exists Step 4:

Q: thank you can u plz solve f&g now

A: OD = 1.9 in  No of fins = 36 k = 34.9 Btuh×ft2F Height H = 0.5 in  Thickness t = 0.035 in  Wall…

Q: 38-41. Identify the Class/Type of machine. Draw the points of application of F, R, and A. 38. Class:

A: given; ⇒draw the point of application of force(F), resisting force(R) and axis A;

Q: 3 in axle tire A B lugwrench

A: Given:The length of the lug wrench, The diameter of the wrench, The shear yield stress,

Q: 4. What are the theorems of Papus and Guldinus used for?

A: It is required to find use of papus and guldinus theorem

Q: I need the answer for number 10.

A: Five Holes, each hole has diameter of 0.500 inches and the holes are equally spaced such that center…

Q: A steel framed building is used to house a food processing plant, the internal atmosphere is humid…

A: Due to food processing inside the building there are always present moisture so the environment…

Q: j) k) Solve for x (x-coordinate of the composite area's Centroid) Solve for y(y-coordinate of the…

A: (j) Write the x-coordinate of centroid for each shape. x1=200-4r3π=200-42003π=115.12…