Calculate the latency (from first bit sent to last bit received) for the following: (a) 100-Mbps Ethernet with a single store-and-forward switch in the path and a packet size of 12,000 bits. Assume that each link introduces a propagation delay of 10 µs and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches.

Calculate the latency (from first bit sent to last bit received) for the following: (a) 100-Mbps Ethernet with a single store-and-forward switch in the path and a packet size of 12,000 bits. Assume that each link introduces a propagation delay of 10 µs and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

2. In the Ethernet packet, the "Data" part is used to contain data send from source to destination and vice versa. The minimum number of data bytes is 46; what if the data is less by 2 bytes
# Write four functions of the data link layer. What is the importance of calculating minimum hamming distance?
At a transmission rate of 10Mbps and propagation speed of 2 × 10² m/s. How many meters of the cable is one bit delay in an Ethemet interface equivalent?
What distinguishes a network that changes between circuits from one that switches between packets is the way in which the data is sent.What is it that TDM accomplishes better than FDM in a network that uses circuit switching?
Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During each time slot 8 bits are sent. What is the total transmission rate of the whole link in kbps?
Calculate the latency (from first bit sent to last bit received) for the following: (a) 100-Mbps Ethernet with a single store-and-forward switch in the path and a packet size of 12,000 bits. Assume that each link introduces a propagation delay of 10 µs and that the switch begins retransmitting immediately after it has finished receiving the packet. (b) Same as (a) but with three switches. (c) Same as (a), but assume the switch implements “cut- through" switching; it is able to begin retransmitting the packet after the first 200 bits have been received.
Calculate the delay x bandwidth product for the following links. Use one-way delay, measured from first bit sent to first bit received. (a) 100-Mbps Ethernet with a delay of 10 μs. (b) 100-Mbps Ethernet with a single store-and-forward switch like that of Exercise 16(b), packet size of 12,000 bits, and 10 μs per link propagation delay. (c) 1.5-Mbps T1 link, with a transcontinental one-way delay of 50 ms. (d) 1.5-Mbps T1 link between two groundstations communicating via a satellite in geosynchronous orbit, 35,900 km high. The only delay is speed-of-light propagation delay from Earth to the satellite and back.
Assume there is a 1 Mbps shared connection (e.g. Ethernet bus). How long (in microseconds) does it take to send a 1000-bit frame over this link?
Computer Science Which of the following statement is true for Path term in SDH Network? a. Points where add/drop signal occurs. b. Points between SDH network Originated and Terminated. c. Points where regeneration of signal occurs. d. Points where Multiplexing/Demultiplexing of signal occurs.
Compute the maximum channel utilization for a MAN which uses CSMA mechanism and has a length of 50 km, and operates at 50 Mbps with a frame length of 2000 bits.
1. Name the advantages of optical fiber over twisted-pair and coaxial cable. 2. Compare and contrast (major points) between a circuit-switched network and a packet-switched network. 3. The two types of networks, datagram and virtual-circuit, need a routing or switching table to find the output port from which the information belonging to a destination should be sent out, but a circuit-switched network has no need for such a table. Give the reason for this difference. 4. What is the Hamming distance for each of the following codewords: a. d (10000, 00100)b. d (00101, 10000) 5. Find the minimum Hamming distance for the following…
Suppose value of K is 1 (Ethernet CSMA/CD), compute backoff time when link capacity (data rate) is: 10 kbps 100 kbps