Calculate the individual quantity of cement, sand, gravel, and water for the concrete pedestal shown (upper base= 1 square foot, lower base= 4 square foot, height=3 ft) assuming the nominal mix design concrete of grade M15 and given the following data: Factor of Safety for Shrinkage=54% density of cement= 1440 kg/m^3 density of sand= 1600 kg/m^3 density of gravel=1560 kg/m^3 w/c ratio= 0.75

Calculate the individual quantity of cement, sand, gravel, and water for the concrete pedestal shown (upper base= 1 square foot, lower base= 4 square foot, height=3 ft) assuming the nominal mix design concrete of grade M15 and given the following data: Factor of Safety for Shrinkage=54% density of cement= 1440 kg/m^3 density of sand= 1600 kg/m^3 density of gravel=1560 kg/m^3 w/c ratio= 0.75

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Given : Width = 1.00m Length = 2.50m Cement = 50kg/bag Using Class A concrete mixture, what is…

A: Given Data:Width = 1.00mLength =2.50mCement = 50kg/bag

Q: in respectively, determine the stress in the steel. E-steel = 29x10^6 Ibs./in^2. E-concrete =…

Q: Calculate the density of the concrete Volume of the bucket = 0.00727 m3 Mass of empty bucket =…

Q: What can you conclude?

Q: According to fuller equation, to draw the maximum density line for aggregate gradation shown below ,…

Q: Calculate the quantities of ingradients required to produce of One cubic meter structural concrete.…

Q: Given the Concrete Mix Ratio of 1:2:2.5, w/c = 0.48, mass of concrete per cubic meter is equivalent…

A: Given data: Concrete mix ratio=1:2:2.5 w/c =0.48 Mass of concrete per cubic meter=2355 kg per cubic…

Q: Problem A sample of a dry coarse grained material of 500 grams was shaken through a nest of sieves…

A: Size of sieve for which 60% of sand passes, D60=2mmSize of sieve for which 300% of sand passes,…

Q: The pycnometer method has been adopted to measure the specific gravity of cement. The following…

A: Pycnometer: A pycnometer is a device used in the civil laboratory device used to measure the density…

Q: Give the value of Plastic modulus for ISHB 250 @ 54.7 kg/m weight.

A: Brief concept introduction- ISHB 250 is the short name for the Indian Standard Heavy Weight Section…

Q: A stone is fully submerged in water. It weighs 450 N in air and 200 N in water. Calculate the volume…

Q: P01: Calculate the modulus of elasticity Ec for each case shown in table: E,=33w¹ √√, psi E=0.043w¹5…

A: Density and compressive strength of concrete samples are given asDensityCompressive strength, f'c180…

Q: For computational purposes, provide virtual Data for the following term and compute for the Bulk…

A: Given Weight of bucket filled with dry coarse aggregate =2.68 kg

Q: Given the table below, determine the BULK SPECIFIC GRAVITY OF GROUP 3. Data and Results Weights…

Q: 2. Solve the following problems. A. Given properties of cement, sand and gravel is presented in the…

Q: Refer to the previous problem. What is the weight of the stone? O 12 N O 13 N O 10 N O 11 N

A: Given data: Weight of stone=7N in water Weight of stone= 8 N in alcohol SG of alcohol=0.8 Unit…

Q: QI\ Write by your own words about 1. The effect of fresh properties on the strength of concrete. 2.…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: According to fuller equation, to draw the maximum density line for aggregate gradation shown below ,…

A: 63% is passing through the sieve 4. 75 mm Similarly 100 % is passing through 19.5 mm sieve 95% is…

Q: Problem 4: Calculate the flexural stresses in the concrete and steel for the beams shown using the…

Q: Air water solids Total Volume Void vatio = 0.89 W.C. = 7%. = 3 5.74 m ³ gravity of solids= solids =…

A: Given data in questionTotal volume 5.74 m3Void ratio 0.89Water content 7%Specific gravity 2.47To…

Q: Estimate the quantities of cement, sand, and coarse aggregate per m of concrete if minimum void…

Q: 1. It is important to know the specific gravity of rock used as concrete aggregate. If a rock weigh…

A: Answer: We are given Rock weight in air = 6.15 N Rock weight in water = 3.8 N We can calculate the…

Q: A. A materials engineer conduct a Moisture Content Test. Here is the result Oven dry Sample (2DD +…

Q: B. A volume of one cum of water is subjected to a pressure increase of 14MP.. 1. Compute the change…

A: 1) negative sign represent the decrease in volume

Q: 2. A concrete mixture given in the table below is produced. The true unit weight of concrete is…

A: Consider the above given table True unit weight of concrete is 2370 kg/m3 C} True mix proportion of…

Q: Given the following data: B. Compact Unit Weight Determination Fine Aggregate a. Weight of measure,…

A: Total weight of sample = (Weight of measure + sample) - (weight of measure) Total weight of sample =…

Q: Given is a concrete mix in which the proportions of cement to fine aggregate to coarse aggregate are…

Q: Discuss the results in the following graph?

A: To

Q: A. Given properties of cement, sand and gravel is presented in the table below: Specific Density,…

A: Given : Specific gravity and density of materials are given. Mass and volume of each material is to…

Q: A. A materials engineer conduct a Moisture Content Test. Here is the result Oven dry Sample (2DD +…

Q: A bucket of cement has a volume of 27,000,000 mm3. The specific gravity of cement is 3.1. Determine…

Q: 4) Use the results in tables 5 & 6 to plot the following graphs; slump vs. water content (L/m^3),…

A: Slum (mm). Water content 5. 6.53 50.…

Question

FIND:

Mass of cement= kg

Mass of sand= kg

Mass of gravel= kg

Volume of water required= liters

Calculate the individual quantity of cement, sand, gravel, and water for the concrete pedestal shown (upper base= 1 square foot, lower base= 4 square
foot, height=3 ft) assuming the nominal mix design concrete of grade M15 and given the following data:
Factor of Safety for Shrinkage=54%
density of cement= 1440 kg/m^3
density of sand= 1600 kg/m^3
density of gravel=1560 kg/m^3
w/c ratio= 0.75

kg
Mass of cement=
Mass of sand=
kg
kg
Mass of gravel=
liters
Volume of water required=

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Using the Table Below, what is the approximate value of the match line if k=100, Ec=6x10^6, J=4, and the rest is the same with the example. Concrete elastic modulus, E. (106 Ib/in²) 10 20 1200 1100 4.5 4.0 30 1000 40 900 3.0 800 50 2.2 700 60 600- 70 500 80 - 800 400 200 100 50 Effective modulus of subgrade reaction, k (Ib/in3) 20 10 90 100 Example: k = 72 Ib/in3 E = 5 x 106 Ib/in? R = 95% (ZR = -1.645) S = 650 Ib/in? J= 3.2 S, = 0.29 APSI = 4.2 - 2.5 = 1.7 W18 = 5.1 x 106 (18-kip ESAL) Solution: D = 10.0 inches (nearest half-inch, from segment 2) C4 = 1.0 10 sninpow ajajɔuon GuIvai) 's 'əunadna Load transfer coefficient, J ~ Drainage coefficient, Cí Match line
clear and complete solution please
I need answer for this please.
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained:Volume of bucket = 14 LWeight of empty bucket = 9.21 kgWeight of bucket filled with dry rodded coarse aggregate:Trial 1 = 34.75 kgTrial 2 = 34.06 kgMeasureSampleA B CWet Mass (g) 521.0 522.4 523.4Dry Mass (g) 491.6 491.7 492.1Absorption (%) 2.5 2.4 2.3Table P 5 . 9 determine the amount of water required to increase the moisture content of aggregate to reach absorption?5.9 Three samples of fine aggregate have the properties shown in Table Trial 3 = 35.74 kga. Calculate the average dry-rodded unit weightb. If the bulk dry specific gravity of the aggregate is 2.620, calculate thepercent voids between aggregate particles for each trial.
Given properties of cement, sand and gravel is presented in the table below: Specific Density, Materials Gravity, kg/m3 Gs Cement 3.21 1,541 Sand 2.60 1,686 Gravel 2.72 1,524 Use 1:2:4 mix design ratio and 52.05 liter of water per 2 bags of cement. Solve for the number of bags for a 31.89m³ of concrete. Where 1 ft = 0.023 m3 %3D
List some Clay minerals and their uses.
4. From the given data shown in the table below, determine the effective specific gravity of aggregates. Round off to two decimal places.
In Hooke and Brown's equation, If we have the value of m , how is the peak value of tensile strength calculated for granite, rhyolite, marble?? qu = 100MPa For marble (m = 7): peak compressive strength =? For rhyolite (m =17): peak compressive strength =? For granite (m = 25): peak compressive strength =?
Present your solution and box your final answer
A box measuring 50 cm x 50 cm x 50 cm is filled to the top with dry coarse aggregate of mass 187.5 kg. The water absorption and specific gravity of the aggregate are 0.5% and 2.5, respectively. The maximum quantity of water (in kg, round off to 2 decimal places) required to fill the box completely is bris
From the given data shown in the table below, determine the effective specific gravity of aggregates. Round off to two decimal places.
Please help with the attached problem