Calculate the delay of the signal between point Vin and node 6 using Elmore delay method Note: Assume the Resistance for each resistor is R and the capacitance for each capacitor is C. H ww O IRC O 2"R°C O 3R°C O 4*R*C O 5'R°C O 6*R*C O7R°C OBR°C O 9*R*C 10"R°C ORC O 12 R°C O None of the other options C

(Heat transfer) The formula developed in Exercise 5 can be used to determine the cooling time, t, caused only by radiation, of each planet in the solar system. For convenience, this formula is repeated here (see Exercise 5 for a definition of each symbol): t=Nk2eAT3fin A=surfaceareaofasphere=4r2 N=numberofatoms=volumeofthespherevolumeofanatom Volume of a sphere sphere=43radius3 The volume of a single atom is approximately 11029m3 . Using this information and the current temperatures and radii listed in the following chart, determine the time it took each planet to cool to its current temperature, caused only by radiation.

One way to determine how healthy a person is by measuring the body fat of the person. The formulas to determine the body fat for female and male are as follows: Body fat formula for women: A1 = (body weight x 0.732) + 8.987 A2 = wrist measurement (at fullest point)/3.140 A3 = waist measurement (at navel) x 0.157 A4 = hip measurement (at fullest point) x 0.249 A6 = forearm measurement (at fullest point) x 0.434 B = A1 + A2 A3 A4 + A5 Body fat = body weight - B Body fat percentage = body fat x 100/body weight Body fat formula for men: A1 = (Body weight x 1.082) + 94.42 A2 = wrist measurement x 4.15 B = A1 A2 Body fat = body weight B Body fat percentage = body fat x 100/body weight Write a program to calculate the body fat of a person.

(Transportation) Road construction requires estimating the expected loads on a road’s pavement over its design life. A common approach for determining this information is to use ESAL values; one ESAL is the load a single 18,000-lb (80,000 N) single-axle truck applies to the road’s surface. The ESAL value for any single-axle vehicle can be approximated by this formula: ESAL=[W18,000]4 ESAL is the equivalent single-axle load. W is the vehicle’s weight (lbs). Using this formula, write, compile, and run a C++ program that determines ESAL values and use it to complete the following chart. The ESAL values should be output in a field width of 10, with six digits after the decimal point.

(Civil eng.) The maximum load that can be placed at the end of a symmetrical wooden beam, such as the rectangular beam shown in Figure 2.20, can be calculated as the following: L=S1dc L is the maximum weight in lbs of the load placed on the beam. S is the stress in lbs/in2. I is the beam’s rectangular moment of inertia in units of in4. d is the distance in inches that the load is placed from the fixed end of the beam (the “moment arm”). c is one-half the height in inches of the symmetrical beam. For a 2” × 4” wooden beam, the rectangular moment of inertia is given by this formula: I=baseheight3=12=24312=10.674 c=(4in)=2in a. Using this information, design, write, compile, and run a C++ program that computes the maximum load in lbs that can be placed at the end of an 8-foot 24 wooden beam so that the stress on the fixed end is 3000lb/in2. b. Use the program developed in Exercise 9a to determine the maximum load in lbs that can be placed at the end of a 3” × 6” wooden beam so that the stress on the fixed end is 3000lb/in2.

(Practice) State whether the following are valid function names and if so, whether they’re mnemonic names that convey some idea of the function’s purpose. If they are invalid names, state why. powerdensity m1234 newamp 1234 abcd total tangent absval computed b34a 34ab volts$ a2B3 while minVal sine $sine cosine speed netdistance sum return stack