CALCULATE THE BASIC CAPACITY FOR LIGHT WEIGHT AND COMMERCIAL VEHICLES FOR A LANE ON A STATE HIGHWAY IN PLAIN COUNTRY. ASSUME THE LENGTH OF LIGHT VEHICLE AS 4.5 M AND COMMERCIAL VEHICLE AS 6.0 M. [TAKE F = 0.4] [USE IRC RECOMMENDATION]

CALCULATE THE BASIC CAPACITY FOR LIGHT WEIGHT AND COMMERCIAL VEHICLES FOR A LANE ON A STATE HIGHWAY IN PLAIN COUNTRY. ASSUME THE LENGTH OF LIGHT VEHICLE AS 4.5 M AND COMMERCIAL VEHICLE AS 6.0 M. [TAKE F = 0.4] [USE IRC RECOMMENDATION]

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Solve the given problems. 1. Determine the distance to the center of mass of the homogeneous rod…

Q: The beam is loaded as shown. which of the following nearly gives the maximum momen of the beam in…

A: Concept:- If the loading is symmetrical then load applied on the beam will be equally divided…

Q: The table below show data collected from flow rate measurement experiment that was carried out using…

A: We will divide volume by time to calculate discharge.

Q: 1. State cofferdam and classify it.

A: Following guideline, first question is answered.

Q: Determine the best hydraulic section for the following geometric

A: ###Determination of best hydraulic section for part i and ii

Q: Three plates are welded together to form the section shown. Dimensions of the cross section areb-4.7…

Q: Classify the structure as statically determinate (Write SD), statically indeterminate (Write only…

Q: 20 kN 20 kN 15 KN 15 kN B 13 5 12 26 E -3 m--3 m- 3m -3m- -3 m- -

Q: A simply supported wood beam that is 13.8 m long carries a 35 kN concentrated load at B. The…

A: Note- the values of shear stresses calculated at point H and K are not given correct in question.…

Q: The hollow core panel is made from plain stone concrete. Determine the dead weight of the panel in…

A: Let us first calculate the whole weight of panel including the holes, Therefore,dead weight…

Q: Determine the largest weight W (in Ib) that can be supported safely by the structure shown in the…

Q: (a) the magnitude of the horizontal shear stress at points A and B. (b) the magnitude of the…

Q: (a) y= i mm Iz = i mm4 S = i mm3 (b) ƠH = i MPa (c) OK = i MPa (d) Omax i MPa

Q: Given the Frame as shown below. Using Method of Members, determine the following if the External…

A: Given Bx= F (-X direction ) Calculate all reaction in terms of F

Q: A normally consolidated clay is consolidated under a stress of 03 =125 kPa, then sheared undrained…

A: Given: σ3= 125KPa, △uf = 40 KPa, Deviator stress = 250 Kpa

Q: Consider the uniformly distributed load shown in the diagram. The load is L = 23N/m. In addition,…

Q: From station 0 + 040, with center height of 1.40 m. fill, the ground line makes a uniform slope of…

Q: when the backfill has properties with: Φ' = 35° and γt = 16.5 kN/m3. The soils in front of the wall…

A: Factor of safety against overturning = Resisting moment / overturning moment Factor of safety…

Q: Classify the structure as statically determinate (Write SD), statically indeterminate (Write only…

A: Finding static indeterminacy

Q: Water is flowing steadily in a horizontal elbow and nozzle combination shown in the figure. The gage…

Q: Interior Angle Traverse Given the bearing of each line of a closed traverse ABCDE, determine the…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 18 kips, w…

Q: Classify the structure as statically determinate (Write SD), statically indeterminate (Write only…

A: A frame structure is given and it has been asked to determine static indeterminacy of the structure.…

Q: mm. Section a-a is located at x = 2.3 m fro on a-a, determine the magnitude of the sh ion a-a,…

Q: The box of negligible size is sliding down along a curved path defined by the parabola y = 0.38x ^ 2…

A: Given, y = 0.38 x2 vB = 30 kmph

Q: Deflection of Beams 1. Determine the midspan deflection of the beam if E = 10 GPa and I= 20 × 10°…

A: Given data: E=10 GPaI=20×106 mm4EI=10×106×20×10-6 kN.m2EI=200 kN.m2

Q: The cross-sectional areas of a column are shown in the figure. Find the maximum allowable value of P…

Q: A student measures the length of his test paper with a ruler for 5 times because his/ her instructor…

A: Given, Number of times length measured = 5 Number of times width measured = 4

Q: In the figure below, A, B, and C are all pin-connected, while D and E are fixed. With x = 9.3, what…

A: Sign convention: Upward vertical force = positive Downward vertical force = negative…

Q: Classify the structure as statically determinate, statically indeterminate or unstable.

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm.…

Q: Determine the loads developed in the column support at 2-A, inc

A: To find foundation reaction at 2 A column

Q: END. (A) FIND THE UNIFORM SHAFT DIAMETER SO THAT THE SHEARING STRESS WILL NOT EXCEED 60 MPa. (B) IFA…

Q: Calculate all the bar force members if P = 30 KN using %3D method of joints.

Q: The beam is loaded as shown. which of the following nearly gives the flexural stress due to tension…

Q: ai 3 m1 to la JF E D --2.5 m -2.5 m -2,5 m 5 kN 3 kN 2 kN

Q: 7. Explain anodizing , galvanising and electroplating

A: As per the guidelines only 1st Q. is to be answered.

Q: Quiz No. 1 (Truss) Given the Truss as shown below with load P1 = X N and P2 = 3X N. Using Method of…

Q: 4 kN 2 kN 2 kN/m B A 3 m -1m

Q: Two 8-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the…

Q: A simply supported wood beam that is 13.8 m long carries a 30 kN concentrated load at B. The…

A: Given data L = 13.8 m a = 75 mm b = 155 mm c = 40 mm d = 390 mm P = 30 KN So, 2L/3 = 2×13.8/3 =…

Q: Problem: A gravity dam in the figure carries water that is 12 m deep on its upstream side. The…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A roller BEoller rollerC

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 20 kips, w…

Q: 2. Draw the shear and moment diagrams for the compound beam. 8000 N 400O N 1600 N/m B E 1000 N/m A D…

Q: The extruded plastic shape will be subjected to an internal shear force of V = 380 lb. Dimensions of…

A: In the question a external plustic shape is subjected to a internal shear force of given value. and…

Q: Determine the reduced live load supported by a typical interior

Q: Problem 2 A simply supported steel beam carries a factored concentrated load of 25 kips at the…

Q: deep upstre ficient of friction between the soil and the is 0.50. y_concrete=23.5 kN/m^3 ow far is…

A: Resisting moment which resist or prevent to loose contact from the surface Unit weight of water…

Concept explainers

Intersection Design

An intersection is a location where two or more roads or railways meet or join. The traffic movement is controlled at the intersection that depends on its design and type. It governs the operation, efficiency, speed, capacity, and safety of the highways, airways, and railways. The movement of the pedestrian causes hazards and delays at the intersection.

Question

CALCULATE THE BASIC CAPACITY FOR LIGHT WEIGHT
AND COMMERCIAL VEHICLES FOR A LANE ON A
STATE HIGHWAY IN PLAIN COUNTRY. ASSUME THE
LENGTH OF LIGHT VEHICLE AS 4.5 M AND
COMMERCIAL VEHICLE AS 6.0 M. [TAKE F = 0.4]
[USE IRC RECOMMENDATION]

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Choose the right answer a rural highway on a level terrain has the following traffic composition: 40 % Passenger cars 30 % trucks 20 % buses 10 % recreational vehicles Find the total volume expressed as pcu/hr. if the total volume is 6000 veh/hr. * a-7620 b-7630 c-7640
The average center to center spacing of vehicles in a simple lane highway is 50 m. The volume of traffic is 600 vehicles per hour. Determine the average speed of the cars using this lane.. help
Problem 08 If the velocity of moving vehicles on a road is 24 kmph, stopping distance is 19 m and the average length of vehicles is 6 m, the basic capacity of the lane is a. 760 vehicles/hour b. 860 vehicles/hour c. 960 vehicles/hour d. 1060 vehicles/hour
If the velocity of moving vehicles on a road is 24 kmph, stopping distance is 19 m and the average length of vehicles is 6 m, the basic capacity of the lane is
4. C per The maximum flow rate on a road is 1000 vehicles hour and the free flow speed is 80 km/h. For an instant when the traffic is flowing at 70% of the maximum flow rate, determine; Ci) the two possible speeds? the two possible spacing the two possible headways? (i) Cili)
Given the data below: Daily Traffic Count Axle Load (Kips) 1000 (single axle cars) 300 (single axle buses) 120 (tandem axle trucks) SN is 5, Pi = 4.2, 22 40 Pr = 3, design life is 20 years, growth rate is 5%, lane distribution factor = 0.45 %3D Calculate the ESAL.
Determine the number of lanes required to provide LOS B (v/c 0.21 – 0.50). 30,000 pcu/day PHF = 7% : 20,000 pcu/day Basic Capacities for highways and urban streets Basic hourly Road Carriageway capacity in pcu in both direction type width, m Highway S4.0 600 4.1- 5.0 1,200 5.1 - 5.5 1,800 5.6 - 6.1 1,900 6.2 - 6.5 2,000 6.6 - 7.3 2,400 7,200 (expressway) 2x 7.0 Urban ~ 6.0 1,200 Street 6.1 - 6.5 1,600 6.6 – 7.3 1,800 2 x 7.0 6,700 Basic Capacities for Multilane Highways No. of lanes per 2 3 direction Hourly capacity, pcu/lane 1,800 1,750 1,700
The 19-Mg truck drives onto the 278-Mg barge from the dock at 25 km/h and brakes to stop on the deck. The barge is free to move in the water, which offers negligible resistance to motion at low speeds. Calculate the speed of the barge after the truck has come to rest on it. 25 km/h 278 Mg 19 Mg Answer: v = i km/h
A section of highway has a speed–flow relationship of the form q = au2 + bu, where q is the traffic flow in veh/h, u is the space-mean speed of traffic in mi/h, and a and b are unknown parameters. It is known that at capacity (which is 3100 veh/h) the spacemean speed of traffic is 28 mi/h. Determine the speed when the flow is 1500 veh/h and the free-flow speed.
Compute the peak hour factor if the hourly volume of traffic is 1800 vehicles/hour and the highest 15-min. volume is 750. (A) 0.5 B) 0.6 c) 0.4 D) 0.3
Calculate the minimum passing sight distance required for a two-lane rural highway that has a posted limit of 72 kph. The local traffic engineer conducted a speed study of the subject road and found the following: Average speed of passing vehicle= 76 kph Average acceleration of passing vehicle= 2.3 kph/sec Average speed of impeder vehicles= 64 kph Show complete solution. Need ASAP. Thank you.
If the velocity of moving vehicles on a road is 24 kmph, stopping distance is 19 m and the average length of vehicles is 6 m, the basic capacity of the lane is a. 500 vehicles/hour b. 750 vehicles/hour c. 960 vehicles/hour d. 1250 vehicles/hour