Calculate anguler velocity of tiller.

Q: The length of a workpiece is 5.25 in. is tapered in the lathe. If the shafting has .035 taper per…

A: GIVEN DATA- LENGTH OF WORKPIECE = 5.25in. TAPER PER FOOT = 0.035 WE HAVE TO FIND AMOUNT OF OFFSET

Q: In Drilling machine, Feed given to drill in this direction makes the hole Select one: a. Downward b.…

A: Given :-  In Drilling machine, Feed given to drill in this direction makes the hole Select one: a.…

Q: Differentiate between Horizontal and Vertical axis wind mills? Give advantages and disadvantages of…

A: Difference between horizontal and vertical wind mills are as follows. Horizontal axis turbine…

Q: The total cost of a milling machine is P937,241 including taxes and it can last up to 9 years. What…

A: please check attached file for solution

Q: Advantage of taper turning by tail stock set over method is that power feed can be used. Select one:…

A:

Q: Explain the job of Rudder

A: The rudder is a primary flight control surface that controls rotation about the vertical axis of an…

Q: W hat are the consequences if a cutting tool chips?

A: Consequences if a cutting tool chips  this is related to chip formation. the chips are formed due to…

Q: C. Shear center is the point in or outside a section through which the shear force applied produces

A: This question is based on the concept of shear center.

Q: What is Benefit for shaft And what is use in Future

A: Benefit for shaft  shaft is thee main part which holds the cranks and pushes the crank to rotate in…

Q: Compare the movement of the lower extremity when you do the squat vs marching in place. What is/are…

A: Two often employed functional exercises to evaluate movement patterns are the single leg squat…

Q: Compute the horsepower output of the following described engine operating at 2000 rpm, bore 3.5 in.,…

A:

Q: 220 rpm speed is equal to rad/s. O a. 14.61 O b. 18.61 O C. -14.61 O d. 23.0

A:

Q: 3. What the horizontal tail is used for? AL,

A:

Q: Performance evaluation of centrifugal pump and sealless pump, trends, cost evaluation, and…

A: Mechanical seals are used to make seal on exit and inlet point of the roatating shaft.

Q: 11. The twist drill is divided into .. main parts Select one: a.4 b.1 C.3 d.2

A: twist drill has three principles parts: the point, the body and the shank

Q: 23. The four-jaw independent chuck can hold Select one: a.ROUND WORK ONLY O b.SQUARE WORK ONLY…

A: Four jaw chuck can hold all of the mentioned shaped by adjusting the individual jaws.

Q: type of vane used in pump centrifugal? a. semi open straight b. semi open curved c. open type curved…

A: Option e is correct

Q: What down the external sources of induced foot?

A: The external sources of induced foot are:-

Q: . Omar Juma is working in shaping machine of a gear manufacturing company. This shaping machine ram…

A: Given Data→ Shaping machine of a gear manufacturing company

Q: The tool life decreases from 0.8 min to 0.2 min due to the increase in cutting speed from 60 m/min…

A:

Q: the net engine power of a tractor is 35 HP, what is the approximate power available at the drawbar?

A:

Q: Convert a speed of 850 rpm into surface speed mm/a. Spindle diameter = 200mm.

A:

Q: the required net power (Pc), whic cing operation is defined by:

A: Required net power (Pc), which the lathe is required to provide for the current cutting operation is…

Q: 6. Approximate a spindle speed of 1000 rpm into rad/s. Spindle diameter = 200 mm 2.25 rad/s .16 mm/s…

A:

Q: Approximate a spindle speed of 1000 rpm into rad/s. Spindle diameter = 200 mm a. 2.25 rad/s b. .16…

A: The rotational speed of the spindle,(N)=1000 rpm The diameter of the spindle,(d)=200 mm Determine…

Q: Advantage of taper turning by  tail stock  set over method  is that power feed can be used. Select…

A: Let us discuss about tailstock offset method.

Q: Regarding drilling, which of the following is wrong?Matkaplarla ilgili olarak aşağıda None Hiçbiri O…

A: Drills have  a very important role in machining and various methods have been devised to increase…

Q: The fuction of fly wheel is to a. store energy during all strokes of engine. b. store energy during…

A: A Flywheel  is a mechanical device that is used to store rotational energy.

Q: Wipers pads on lathe machines are used between slides and slideways designed to be cleaned by…

A: The wipers ought to be evacuated, cleaned, and re-saturated with oil routinely. You ought to never…

Q: Hydraulics.   Derive the formula of Upper not down.

A: In this problem, we have to derive the height of liquid in a spherical container which has a…

Q: 10. Formula for cutting speed of the shaper, tell the meaning of each variables.

A: SHAPER In shaping, the cutting tool is held in the tool post located in the ram, which reciprocates…

Q: H6?4 leaves dhe tidad blede of Iso m/s the man at rotal diameler Gu Speed Bat blade ir 35 3500 apm…

A: Given data: The speed of the fluid when it leaves the fixed blade is v = 150 m/s. The mean rotor…

Q: explain 4 stroke cycle in the correct order that it happend

A: Dear student please rate me postive :) Stay safe stay happy ! Answer- Stroke is defined as the…

Q: OnSTEDDY TOW 6-Natural and Forced flow

A: This question is based on the concept of flow of fluid in fluid mechanics.

Q: Tool life testing on a lathe machine under the conditions given value of n and C as 0.12 and 130. If…

A: Given: Value of n= 0.12 Value of C= 130 Velocity, v=90 m/min C is increased by 10 %

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.