C2 The next two questions refer to the following figure. The switch is initially open and both capacitors are initially uncharged. All resistors have the same value R, and both capacitors have the same value C. R2 bat R1 (f) 1 pt. Immediately after the switch is closed, which resistor has the most current through it? (i) R1 (ii) R2 (iii) R3 (iv) R1 and R2 (v) R2 and R3 (vi) All have the same current (g) 1 pt. A long time after the switch is closed, which resistor has the most current through it? (i) R1 (ii) R2 (iii) R3 (iv) Rị and R2 (v) R2 and R3 (vi) None have current

C2 The next two questions refer to the following figure. The switch is initially open and both capacitors are initially uncharged. All resistors have the same value R, and both capacitors have the same value C. R2 bat R1 (f) 1 pt. Immediately after the switch is closed, which resistor has the most current through it? (i) R1 (ii) R2 (iii) R3 (iv) R1 and R2 (v) R2 and R3 (vi) All have the same current (g) 1 pt. A long time after the switch is closed, which resistor has the most current through it? (i) R1 (ii) R2 (iii) R3 (iv) Rị and R2 (v) R2 and R3 (vi) None have current

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
When the switch is closed in above circuit, what is the voltage on the inductor, resistor R1 and R2 after 2.2us , assuming 0 V on the inductor to start?
The circuit in the figure below contains two resistors, R1 = 4.00kΩ and R2 = 5.00kΩ, and two capacitors, C1 = 4.00uF and C2 = 5.00uF, connected to a battery with emf E = 120V. If no charges exist on the capacitors before switch S is closed, determine the charge q1 on capacitor C1 1.00ms after the switch is closed. Determine the charge q2 on capacitor C2 1.00ms after the switch is closed.
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
1. A purely resistive circuit the current is leading by 90° with respect to voltage. 2. A purely inductive circuit the current is lag behind the voltage by 90°. 3. A purely capacitive circuit the current is lead by 90° with respect to the voltage. 4. A capacitor element stored magnetic energy. 5. An inductor element stored electrical energy. 6. Resistor elements consume power. 7. Angle between current and voltage is called power. 8. The power factor angle for a purely resistive is zero. 9. The power factor angle for a purely inductive load is -90°. 10. The power factor of a purely capacitive is leading.
Three 20uF capacitors are connected in series with each other. A 1k ohm resistor and an LED connected in series to each other as well, but branched in parallel to all three capacitors. How long would the LED stay lit after power is removed? What current would flow through it during the charge cycle if VT=9v?