C. Problem Solving. Draw the circuit and show your complete solutions. 1. Given the value of a 6-ohm resistor and an unknown impedance coil in series across a 120V, 60Hz source. Determine the value of the coil inductance (L) if the circuit draws a current of 12A and a real power of 1152Watts.

C. Problem Solving. Draw the circuit and show your complete solutions. 1. Given the value of a 6-ohm resistor and an unknown impedance coil in series across a 120V, 60Hz source. Determine the value of the coil inductance (L) if the circuit draws a current of 12A and a real power of 1152Watts.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: A numeric system (e.g. a numeric keypad) generates numbers 0 to 9 in binary. You are asked to design…

A: For the given problem the truth table must be derived and the same can be used for obtaining the…

Q: ii) Just show induced current directions on figure 5 by using Lenz's law. Current I is constant and…

A: Note: We are authorized to answer one question at a time, since you have not mentioned which…

Q: The slight sideward motion of a shaft is called end play. The end play in theshaft of a rotor for an…

A: The end play of the rotor of an electric motor should be, End play ≤132 inch The given motor has an…

Q: Determine I for the circuit given below. Also,find the voltage gain. 3 ΚΩ SV 3VI 10 ΚΩ Μ 10 ΚΩ Μ Μ 3…

Q: How many different numbers can be obtained using five binary bits? O 63 31 32 63

A: We need to select correct option for given statement

Q: A four-pole, 50Hz induction motor has a full- load slip of 5 percent. The rotor speed of this motor…

A: Given,For a induction motor,Pole, P=4Frequency, f=50 HzFull load slip, S=5%

Q: Let St, x(t) = t. = 2 t, 0 ≤ t ≤1 1≤t≤2 be a periodic signal with fundamental period T = 2 and…

Q: Example 20. Calculate the power drawn in a circuit given the following voltage and current…

Q: 1- A source emf of 5 V supplies a current of 3A for 10 minutes, the energy provided in this time (a)…

A: We need to find out energy for given voltage and current .

Q: or not. Given y(n) = x(n) + x(n-1)+x(n-2). Find whether the system is stable

A: We have an system as, y(n) = x(n) + 18x(n - 1) + 13 x(n - 2) And we have been asked to check whether…

Q: Find the damping ratio and natural frequency for each second-order system shown below and show that…

A: Given data, Transfer function is given as, Ts=5s+3s+4=5s2+7s+12

Q: 7.27. A linear time-invariant discrete-time system has transfer function 3z H(z) = (z+0.5) (z - 0.5)…

A: Given, Hz=3zz+0.5z-0.5x(n)=u(n) For initial conditions y(-1) and y(-2), the output response is…

Q: 7.27. A linear time-invariant discrete-time system has transfer function 3z H(z) = (z+0.5)(z- 0.5)…

A: Given:- transfer function Hz=3zz+0.5z-0.5 Output response, yn=0.5n-3-0.5n+4un We have to find…

Q: 3. Calculate the mesh current 11 for the circuit below. *

A: The required mesh current can be calculated by using the mesh analysis of the given circuit. The…

Q: 2. Relation between currents according to KCL is

A: In this case, the relation between the currents in the given circuits needs to be determined:

Q: Find the Boolean expression for logic circuit shown in Fig.1 below and reduce it using Boolean…

Q: What is the change in the bandwidth of the signal in FM when the modulating frequency increases from…

A: Given information: The modulating frequency corresponding to an FM signal changes from 12 kHz to 24…

Q: (6) Find the Boolean expression for logic circuit shown in Fig.1 below and reduce it using Boolean…

A: We need to find logic expression of given circuit

Q: Prove the following Boolean identities. (i) XY+YZ+ YZ=XY+Z (ii) A.B+A.B+A.B=A+B

A: The given Boolean identity can be verified by using the postulates and theorems of Boolean algebra.

Q: The circuit shown below on the left has the following parameters: Vs = 11 V Is=7A R₁ = 1.20 R₂=2.20…

Q: Q.) The circuit shown below is an idealized forward converter. Assuming an input voltage Vd=40V,…

A: The forward converter, a DC/DC converter, raises or lowers the output voltage and offers galvanic…

Q: Can you explain to me the properties of Laplace transform by solving a differential equations as I…

A: EXPLANATION There are following steps to follow 1- TAKE THE LAPLACE OF…

Q: Two point charges, q₁ = q and q2 = 3q, are 25 cm apart. They repel each other with a force of 2.7 N.…

A: Given data, Charges is given q1=q, q2=3q Distance between charges r=25 cm = 0.25 m Force between…

Q: Find the decimal equivalent of the binary number (1011.011)2.

A: Introduction :- Binary to decimal conversion - A binary number is converted into decimal equivalent…

Q: the standing wave ratio.

A: Given: lossless transmission line having Za=50Ωlength=4.334mkr=0.4∠45°λ=2m if Vs='100V find 1)The…

Q: Imagine that you're told to install a grounding electrode conductor to the TMGB. Based on this…

A: As per BARTLEBY GUIDELINES, For Multiple Questions, we have to answer only first question. So I…

Q: closed-loop voltage gain of the amplifier circuiti

Q: e 3,12. In the circuit shown in Fig. 3.12.1, the switch is moved mA to B at f-0. Find e(t) for t>0.…

A: Solution !!

Q: (TCO 6) Determine the resonance frequency of the tank circuit shown in the figure. The individual…

A: The resonance frequency of the LC tank circuit is given by the expression as shown below:…

Q: 3. Solve the values of VB and I for the Single Stage Transistor Common Emitter Amplifier circuit…

A: The required parameters of the voltage divider biased common emitter amplifier circuit can be…

Q: Explain Permanent magnet moving instruments. coil

A: The permanent magnet moving coil instruments are most accurate type for d.c. measurements.The action…

Q: Design a suitable 8 section starter for a 14.92 kW, 250 volt, 1000 rpm d.c. shunt motor from the…

Q: A three-phase, 460 V, 98hp 1,60 Hz, four-pole induction machine delivers rated output power at a…

A: We have an induction motor with, Supply Voltage (Vl) = 460 V Power Output = 98 hp Frequency (f) = 60…

Q: What is the change in the bandwidth of the signal in FM when the modulating frequency increases from…

A: Given information: The modulating frequency corresponding to an FM signal changes from 12 kHz to 24…

Q: 3. Determine whether the systems with the following characteristic equations are stable or unstable:…

Q: 1. The instantaneous value of current in an a.c.circuit at any time t seconds is given by: i-50…

A: Given data, Current equation is given as, i=50sin100πt-0.45 mA

Q: A step-up transformer is 91 percent efficient and has 81 primary turns and 628 secondary turns. If…

Q: The reactance of O 100 Ohms 000 48.48 Ohms 87.46 Ohms 1.64 Ohms

A: Given data, Impedance is given, Z=100∠610

Q: The reactance of the Impedance Z=100 261 ° is: O 100 Ohms 48.48 Ohms 87.46 Ohms 1.64 Ohms

Q: What is the maximum modulating frequency allowed in commercial FM broadcastings? a. 40 KHz b. 75 KHz…

A: The correct option along with the explanation has been provided in the following section.

Q: To achieve 75 percent modulation of a carrier of V, 190 V, what amplitude of the modulating signal V…

A: Modulation index is given, m=75 %=0.75 Amplitude of carrier signal Vc=190 V

Q: Consider the circuit shown in Figure 1. The capacitors have the same plate area. The capacitance of…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: The resonant frequency is 125 kHz. Find bandwidth, C, and the quality factor, Qs. 10 mH C 1.257ΚΩΣΤ.

A: Given series RLC circuit, Where, Resonant frequency, fo=125 kHz Resistance, R=1.257 kΩ Inductance,…

Q: The equations for Y₁, Y₂ and Z₁ are shown below for a Asynchronous state machine Y₁ = x₁x₂ + y₂y₂x₂…

Q: The voltage across a 81 mF capacitor is 15.4 V. How much energy is stored in the capacitor in W?…

A: Given: Capacitance, C=81 mF Voltage across capacitor, V=15.4 V

Q: What are the 5 countries that have the greatest installed capacity for the generation of energy from…

A: Renewable Energy:- The energy that is produced by natural processes and constantly replenished is…

Q: 2-2m. If Vs = 100 volts, find: (use crack diagram) A lossless transmission line having Z-5002,…

A: Given: Z0=50 ΩVS=100 VKr=0.4<45λ=2 Find: 1. Standing wave ratio 2.Voltage standing pattern

Q: Q3: a) Design a microstrip spiral inductor (square shaped) with an inductance of 2 nH. Sketch the…

A: Given: C1=1.27C2=2.07C3=0.18C4=0.13μ0=4π×10-7H/mL=2 nH Find: Design the microstrip spiral inductors…

Q: A load of 500 kVA operates at 0.6 lagging power factor on 1100 V, 50 Hz mains. The power factor of…

Q: image480

Question

C. Problem Solving. Draw the circuit and show your complete solutions.
1. Given the value of a 6-ohm resistor and an unknown impedance coil in series across a 120V, 60Hz
source. Determine the value of the coil inductance (L) if the circuit draws a current of 12A and a real
power of 1152 Watts.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Sinusoids and Phasors of Alternating Circuit

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. Now what is the minimum AC voltage rating of each capacitor?
1. Enumerate five formulas for five series connected inductances across Vt source and draw the circuit. 2. Enumerate five formulas for five parallel connected inductances across Vt source and draw the circuit.
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
A 25-ohm resistor connected in series with a coil of 50-ohm resistance and 150-mH inductance. What is the power factor of the circuit? The standard frequency is 60 Hz. Show complete solution.
Two impedance coils A and B are connected in series to a 111-volt ac source. Coil A has a resistance of 12 ohms and an inductive resistance of 16 ohms. Coil B has a resistance of 24 ohms and an inductive reactance of 10 ohms. Calculate the voltage drop across each coil. Only in rectangular form
TOE This is a photo of a capacitor that corrects the power factor in an AC setup, in DC it is used in electronic board for appliances and other small devices. Tell me something about this photo.
For the series RL circuit shown in the figure below, answer the following questions and justify your answer.If the current is kept constant, does the coil have inductance?If the current is kept constant, does the coil affect the current value?Can the reverse emf ever be greater than the battery emf?
An inductor of 150hms and resistance of 10 Ohms are connected in series to a 230V, 50 Hz ac supply. Determine the active and reactive power and power factor in the circuit.
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…