Question 2. (C part )Solve a part (i,ii,iii)All parts of C plz and take a thumb up plz Question 2(a) The amplitude and phase response of the Colpitts oscillator utilised in a metaldetector is depicted in Figure Q2. (a)ii.iii.GainL50Figure Q2. (a)i. Identify the oscillation frequency of the oscillator.Hl.iii.100150200(b) Considering the RC circuit shown in Figure Q2. (b)RwwVinPhaseWhat is the feedback voltage of the oscillator if the output voltage is 25V?iv.If we wish to increase the gain of this circuit by a factor of 10, how would youchange the value of the components of the oscillator.270⁰Design and plot the circuit diagram of the oscillator indicating all componentsvalues. Given that the inductor value is 3μH.180⁰90⁰Frequency AfzVoutFigure Q2. (b)Find the Laplace transfer function of the circuit. Then Identify the gain and thetime constant (r) of the circuit.If you wish to increase the time constant by two folds, what changes wouldyou consider in the circuit.Find out (1) given that vin (t) = -3, R= 5 MQ and C=2μF (c) You are tasked to manufacture a parallel plate capacitor with a capacitance of 60μF,using a dielectric with permittivity of 5 F/m².1.Identify the dimensions required for the capacitor.ii.iii.Identify the charge stored in the capacitor if the potential difference betweenthe plates was 40volts.Determine the energy stored in the capacitor and the average power developedif the energy is dissipated in 3ms.

Note: When metallic plates are connected through a DC power supply, Positive and Negative charges…

(c) You are tasked to manufacture a parallel plate capacitor with a capacitance of 60μF, using a dielectric with permittivity of 5 F/m². 1. Identify the dimensions required for the capacitor. ii. Identify the charge stored in the capacitor if the potential difference between the plates was 40volts. iii. Determine the energy stored in the capacitor and the average power developed if the energy is dissipated in 3ms.

(c) You are tasked to manufacture a parallel plate capacitor with a capacitance of 60μF, using a dielectric with permittivity of 5 F/m². 1. Identify the dimensions required for the capacitor. ii. Identify the charge stored in the capacitor if the potential difference between the plates was 40volts. iii. Determine the energy stored in the capacitor and the average power developed if the energy is dissipated in 3ms.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter19: Capacitors

Section: Chapter Questions

Problem 3RQ: A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted...

See similar textbooks

Similar questions

Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 - Hz power line. An ammeter indicates a circuit current of 8.6 amperes. How much current is flowing through the 40F capacitor?
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
In a pure capacitive circuit, does the current lead or lag the voltage?
4. In what form is the energy of a capacitor stored?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
What frequency must be applied to a 33-mH inductor to produce an inductive reactance of 99.526 ?
List the five capacitor replacement rules.
Can current flow through a capacitor?
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?