c) A TV signal was transmitted with peak to peak voltage of 4 and 34 dB signal to quantization noise power when the transmission bandwidth and Nyquist interval of 25200 KHz and 0.238 microsec respectively. Calculate; 1- The maximum transmission power in watt when the transmission channel resistance of 300 ohm. 2- The signaling rate. 3- The quantization level.

c) A TV signal was transmitted with peak to peak voltage of 4 and 34 dB signal to quantization noise power when the transmission bandwidth and Nyquist interval of 25200 KHz and 0.238 microsec respectively. Calculate; 1- The maximum transmission power in watt when the transmission channel resistance of 300 ohm. 2- The signaling rate. 3- The quantization level.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

75 ohm Coax cable Microphone 0.4 V output 150 feet of coax cable with a gain of -4 dB/100 feet & a Vf of 77% Modulator/ transmitter G=15 5. Po at point ( 2 )in dBm. Carrier Frequency is 100 MHz Figure 1 For the system shown in Figure 1 above, determine the following: 4. Power input at point 1) in mW & dBm. 7. Wavelength in the coax, in cm. 6. Gain of the 150 meters of coax cable, in dB. 3 Amplifier 1 G=20 db 50 ohm Terminator 2-way splitter The signal is 3 dB down at each port Po 5
Q. Choose the correct answer (.. 1. increases as the length of channel increases. (interference, distortion, additive noise, attenuation). 2. 100% modulation is produced in AM when carrier frequency exceeds signal frequency, amplitude equals signal amplitude, amplitude exceeds signal amplitude). 3. A 10 MHz carrier of peak value of 10 V is amplitude modulated by a 10 kHz signal of amplitude 5 V. The amplitude of each sideband frequency is 4. A Phase-Locked Loop (PLL) is a feedback circuit consisting of VCO, all of the above). 5. The line connecting the positive and negative peaks of the carrier waveform is called (Peak line, Maximum amplitude, Modulation index, Envelope) 6. Thermal noise power is proportional to (T², 1/T, T, T'2) 7. Which of the following is an advantage of SSB over DSB? (No change in spectrum space, Reduce in spectrum space, Carrier is suppressed, Power is not wasted on the carrier). 8. Which one of the following is not true with respect to SSB signal? (Hard to…
A message signal consisting of 2 tone signals at 100 Hz and 600 Hz frequencies with amplitudes of 1V and 3V, respectively, will be transmitted by modulating with DSB. The frequency of the carrier signal is 2 kHz. Which of the following statements are true? I. The bandwidth of the modulated signal is 1.2 kHz. ii. The dissipated power of the message signal on a 1ohm resistor (normalized) is 4.5 Watts. iii. The frequency components of the modulated signal are at 1.7 kHz, 1.9 kHz, 2.1 kHz, 2.3 kHz. a) All of above b) only i c) i and iii d) only iii
A carrier signal given by 10cos27Tx108t volt is FM modulated by single tone message 4cos2Tx103t volt if the modulation constant is 1000 Hz/Volt a) Compute max. frequency deviation and deviation ratio. b) Write the equation of modulated wave. c) Sketch the spectrum. d) Calculate sidebands carrier and total power
Problem 4. A carrier wave of frequency 25 MHz is frequency- modulated by a sine-wave of amplitude 3 volts and frequency 4 kHz. The frequency sensitivity of the modulator is 12 kHz per volt. a. Determine the approximate bandwidth of the FM wave using Carson's rule. b. Repeat part (a) assuming that the amplitude of the modulating wave is doubled. c. Repeat part (a) assuming that the modulation frequency is doubled.
Q3: A sinusoidally modulated AM waveform is shown below, Determine: 1. Peak amplitude of the upper and lower side frequencies. 2. Peak amplitude of the unmodulated carrier. 3. The modulation index and it is percentage. 4. The total power and the power efficiency. 5. Plot the frequency and the power spectrum of the modulated signal if the frequency of the carrier and the modulating signal are 2MHz and 15KHz respectively. 12 6 0 -6 -12 T
None
Q2. A'single tone is modulated using WBFM transmitter. The total power is 450 watts into a 5 2 resistive load. Determine the minimum modulation index, where the average power of the second and third sidebands are equal. Under this condition determine: 1. The average power in all sidebands. 2. The ratio of the first sideband power to the total power. 3. The third sideband power, if the modulation index is reduced to maintain maximum first sideband power and keep wideband transmission.
Wavelength division multiplexing, to put it briefly.
The power of operating frequency in AM station is 145 W, and there is 89% modulation depth. (assuming single side band suppressed carrier). What is the power of the side bands?
Discuss the concept of electromagnetic interference (EMI) and how it can affect signal quality in wired transmission media.