Answered: By taking the limit as DT2 DT1, show…

By taking the limit as DT2 DT1, show that when DT1 = DT2 for a heat exchanger, the DTlm relation reduces to DTlm = DT1 = DT2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Can you please give me an analysis of heat tranfers in heat exchangers?
It is planned to build a geothermal power plant for electricity generation purposes. The subsoil water reaches temperatures close to 170 ° C while the ambient temperature is 20 ° C. Find the maximum efficiency that a geothermal plant could aspire to if installed in that location. Ans: η=33.85%
A countercurrent heat exchanger was designed with an overall heat transfer coefficient of 900 kcal/hr-m-°C. The heat transfer area of a newly designed heat exchanger is 7 m². Over a period of time, its overall heat transfer coefficient has fallen to 450 kcal/hr mt²°C due to fouling. Given: Specific heat of hot fluid = 1 kcal/kg °C Hot fluid entering temperature = 90°C Hot fluid leaving temperature = 65°C Cold fluid entering temperature = 25°C Cold fluid leaving temperature = 40°C Required: How much additional area is to be added to maintain the same rate of heat transfer? Need asap pls
HERE ARE SOME APPLICATIONS OF SHEEL AND TUBE HEAT EXCHANGER: Power Generation HVAC Marine Applications Pulp and Paper Refrigeration Pharmaceuticals Air Processing and Compressor Cooling Metals and MiningPLEASE MAKE A EXPLANATION FOR THIS
Please answer all parts or leave for someone else to answer i will give you a very positive feedback.
Water must be heated from 15 to 50°C in a simple double-pipe heat exchanger at a rate of 3,500 kg/h. The water is flowing inside the inner tube with steam condensing at 110°C on the outside. The tube wall is so thin that the wall resistance may be neglected. Assume that the steam-film coefficient h_0 is 11 kW/m^2 °C. What is the length of the shortest heat exchanger that will heat the water to the desired temperature, considering an optimal diameter for the tube? Checking several table values, the following properties of water for this scenario are: p = 993 kg/m^3 k = 0.61 W/m °C \mu (viscosity) = 0.78 cP Cp = 4.19 J/g °C
3.36 Both C's in a parallel-flow heat exchanger are equal to 156 W/K, U 327 W/m²K and A = 2 m². The hot fluid enters at 140°C and leaves at 90°C. The cold fluid enters at 40°C. If both C's are halved, what will be the exit temperature of the hot fluid?
A long, thin-walled double-pipe heat exchanger with tube and shell diameters of 0.01 m and 0.025 m, respectively, is used to condense refrigerant-134a with water at 20°C. The refrigerant flows through the tube, with a convection heat transfer coefficient of hi= 4100 W/m² °C. Water flows through the shell at a rate of 0.3 kg/s. The thermal resistance of the inner tube is negligible since the tube material is highly conductive and its thickness is negligible. Both the water and refrigerant-134a flows are fully developed. Properties of the water and refrigerant-134a are constant. Water properties: p = 998 kg/m³, v=u/p-1.004x 10-6 m²/s, k = 0.598 W/m. °C, Pr = 7.01 Cold water D Do
SEMIFINAL PROJECT IN ME 3215 COMBUSTION ENGINEERING PROBLEM: Cooling water for 507 Horsepower Diesel Engine is to be cooled by using an intermediate cooling heat exchanger as follows. At Counterflow Heat exchanger. Jacket water in --- 60 °C Jacket water out 38 °C Tower water in 27 °C Tower water out - -54 °C To be done: Make the necessary valid assumptions and calculate the flow through heat exchanger for the following quantities: kg 1. Jacket water, in sec kg 2. Tower water, in sec to coling o NEAT EXCNANGER DESEL ENGE from cool
i need the answer quickly
QUESTION 7 A local brand of water heater has offered a counterflow concentric tube heat exchanger, consisting of thin walled copper drains with a diameter D; = 50 mm. Waste water from the shower enters the heat exchanger at Thi= 38 °C while fresh water enters the room at Te,j= 10 °C. The waste water flows down the vertical drain wall in a thin, falling film and providing h, = 10 kW/m²·K. i. If the annular gap is d = 10 mm, the heat exchanger length is L = 1 m, and the water flow rate is m = 10 kg/min, determine the heat transfer rate and outlet temperature of the warmed fresh water. ii. If a helical spring is installed in an annular gap so the fresh water is forced to flow a spiral path from the inlet to the fresh water outlet, resulting in he = 9050 W/m²-K, determine the heat transfer rate and outlet temperature of the fresh water. iii. Based on the result from Q5(b), calculate the daily saving if 15,000 guests each take 10 minutes shower per day and cost of water heating is…