Bottom chord of truss is composed of two angle bars each having a dimension of 185 mm x 146 mm x 8.7 mm. Between them is a gusset plate, 9.5mm thick. At each end of joints, four 19mm-dia. bolts are fastened along the gage line, having an edge distance of 44 mm and 59mm pitch. Use A36 steel Fy 248 MPa Fu = 400 MPa %3D spacing of bolt = 68.9 mm %3D 9 5mm trick gunset plate edge dist Compute the capacity of the bottom chord based on block shear strength, in KN. uad

Bottom chord of truss is composed of two angle bars each having a dimension of 185 mm x 146 mm x 8.7 mm. Between them is a gusset plate, 9.5mm thick. At each end of joints, four 19mm-dia. bolts are fastened along the gage line, having an edge distance of 44 mm and 59mm pitch. Use A36 steel Fy 248 MPa Fu = 400 MPa %3D spacing of bolt = 68.9 mm %3D 9 5mm trick gunset plate edge dist Compute the capacity of the bottom chord based on block shear strength, in KN. uad

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole Compute the nominal strength in bearing on Gusset plate only (since this will govern, it has smaller thickness than the main member PL ½ x 6)
I the Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf=120mm d=550mm d'=80mm fc'=34MPA fy=415MPA USE NSCP 2015 mm2 A.Mu = 1400KN-m, As = mm2 B.Mu = 1700kN-m, As = mm2, As' = CS Scanned with CamScanner
16) what is the tensile yielding capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
5 please help meee
SOLVE FOR1 HR
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 2L5 x 3 x16 LLBB Determine the allowable tensile strength for ASD. Select one: а. 52.1 b. 104.2 c. 87.8 d. 43.9
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co
SITUATION B. strength and the allowable strength considering the following members. Analyze the members separately except for No.7. 5. 6. Given the connection below bolted with M22 bolts, solve for the design tensile A992 W360x122 A36 L152X102X14.3 7. Built-up Section with Ey=345 MPa and Fu=450 MPa W 360 X 122 75 100 mm 100 -P L152X102X14.3 bf/2
Five M20 8.8/ bolts are used in the connection between a beam and a column. Both sides of the cleat plate are welded to column using fillet weld (Manual metal arc AS4855 B-E43XX) with size of 5 mm. The design force transferred from beam to column is 300 kN. The cleat plate has thickness of 12 mm, fy = 300 MPa, and fü = 360 MPa. Determine the unit stress sustained by the weld