Binary Counters Objective: Design. construct, and test a three-bit counter that counts up or down. A disable input D determines whether the counter is on or off. If D=1, the counter is disabled and remains at its present count even thoughclock pulses are applied to the flip-flops. • If D=0, the counter is enabled and a second input, x, determines the directionof the count. • If x=1, the circuit counts the sequence 00, 01, 10,11 and the count repeats. • If x=0, the circuit counts the sequence 11, 10, 01, 00 and the count repeats. (Do not use D to disable the Clock) Note: Design the sequential circuit with D and x as inputs. Submission: Reports must include all schematics and cost of design. Compare your results with other solutions. (Costs, design....). Define why your design is better.

Binary Counters Objective: Design. construct, and test a three-bit counter that counts up or down. A disable input D determines whether the counter is on or off. If D=1, the counter is disabled and remains at its present count even thoughclock pulses are applied to the flip-flops. • If D=0, the counter is enabled and a second input, x, determines the directionof the count. • If x=1, the circuit counts the sequence 00, 01, 10,11 and the count repeats. • If x=0, the circuit counts the sequence 11, 10, 01, 00 and the count repeats. (Do not use D to disable the Clock) Note: Design the sequential circuit with D and x as inputs. Submission: Reports must include all schematics and cost of design. Compare your results with other solutions. (Costs, design....). Define why your design is better.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

In digital electronics and modern computer hardware, a flip-flop is sequential digital circuit used as a basic memory element. It has two stable states and can be used to store state information. One of its states represents ‘1’ while the other represents ‘0’. The most common types of flip-flops are SR-flip-flop, JK-flip-flop, and D flip-flop. When used in a finite-state machine, the output and next state depend not only on its current input, but also on its current state (and hence, previous inputs).
In digital electronics and modern computer hardware, a flip-flop is sequential digital circuit used as a basic memory element. It has two stable states and can be used to store state information. One of its states represents ‘1’ while the other represents ‘0’. The most common types of flip-flops are SR-flip-flop, JK-flip-flop, and D flip-flop. When used in a finite-state machine, the output and next state depend not only on its current input, but also on its current state (and hence, previous inputs). Figure 1 D-Flip-flop with clock pulse (CP) Figure 1 shows a D flip-flop with clock pulse (CP). D is directly passed from stage1 to stage 2 through NAND gate and passed as inverted through gate 5 and gate 4. The input D is always sampled when the system CP is 1. Considering the memory element in Figure 1, perform the following tasks: Design FSM for the Figure 1 Simulate the Figure 1 using C. Write 400 words report on shift and…
In digital electronics and modern computer hardware, a flip-flop is a sequential digital circuit used as a basic memory element. It has two stable states and can be used to store state information. One of its states represents ‘1’ while the other represents ‘0’. The most common types of flip-flops are SR-flip-flop, JK-flip-flop, and D flip-flop. When used in a finite-state machine, the output and next state depend not only on its current input but also on its current state (and hence, previous inputs). Stage 2 Stage 1 Figure 1 D-Flip-flop with clock pulse (CP) Figure 1 shows a D flip-flop with clock pulse (CP). D is directly passed from stage1 to stage 2 through the NAND gate and passed as inverted through gate 5 and gate 4. The input D is always sampled when the system CP is 1. Considering the memory element in Figure 1, perform the following tasks: Design FSM for the Figure 1
In digital electronics and modern computer hardware, a flip-flop is a sequential digital circuit used as a basic memory element. It has two stable states and can be used to store state information. One of its states represents ‘1’ while the other represents ‘0’. The most common types of flip-flops are SR-flip-flop, JK-flip-flop, and D flip-flop. When used in a finite-state machine, the output and next state depend not only on its current input but also on its current state (and hence, previous inputs). Stage 2 Stage 1 Figure 1 D-Flip-flop with clock pulse (CP) Figure 1 shows a D flip-flop with clock pulse (CP). D is directly passed from stage1 to stage 2 through the NAND gate and passed as inverted through gate 5 and gate 4. The input D is always sampled when the system CP is 1. Considering the memory element in Figure 1, perform the following tasks: design FSM for 8-bit shift register and simulate it using C++, which can multiply or divide the…
Q5: Write the counting states for this counter: Q0- Q1- ffo ff1 ff2 ff3 1HJ aF 1 K Q'F K at K Q CK •
The state table for a counter is given below. Fill the empty cells of the state/excitation table assuming that JK flip-flop is used for bit A T flip-flop is used for bit B SR flip-flop is used for bit C Write 0 or 1 or X in each cell. ("X" is corresponding to the "don't care" condition.) A(t) B(t) c(t) 0 0 0 0 1 1 1 Present State 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 A(t+1) B(t+1) C(t+1) 0 0 1 1 1 0 1 Next State 0 1 1 0 1 0 0 1 0 0 1 0 0 1 0 1 1 JA 4 4 4 45 45 4 Flip-Flop Inputs ΚΑ Тв + ◆ Sc ♦ ◆ ◆ + + ◆ Rc 4
Ex4: Design a counter with 7 flip-flops that goes through the following binary repeated sequence: 0, 1, 3, 7, 6, 4. Show that when binary states 010 and 101 are considered as don't care conditions, the counter may not operate properly. Find a way to correct the design. Sol: • The number of flip-flops required is three. • Table below shows the desired circuit excitation table. Present Next Flip-flop inputs state state ABC ABC TA TB Tc 000 001 0 0 1 001 011 0 1 0 010 XXX X X X 011 111 1 1 0 100 000 1 1 0 101 X XXX X X 110 100 0 1 0 111 110 0 0 1 complete the solution
write a verilog code for counter which starts from 13 and stops at 113.
Q1: Design a Moore FSM to detect if an input sequence is divisible by 5. Each cycle a new bit comes as input towards LSB (e.g. if the current sequence is '1011' and the input is '0', the new sequence is '10110'). The FSM outputs a logic 1 if the sequence is divisible by 5, otherwise it outputs a logic 0. The starting point for the state diagram and a description of what the state does is depicted below. And assume initially the system is in state S0. a) Draw the Moore state diagram for this FSM using a minimum number of states. b) Draw the excitation table for the states. Define the states in order; e.g. S0 = 000, S1 = 001 etc. c) Write the minimum SOP Expression for all the bits of the states and the output 'O'. I: 0 so All 0 S1 Remainder 1
T flip flops to design a counter with repeated binary sequence: 0,1,3,5,7. The circuit is to be designed by treating unused states as don’t care conditions. 1. Sketch the state diagram 2. Derive the state table 3. Implement the circuit.
令all Homework..pdf > Q1: Design a synchronous binary counter using D flip- flop with the sequence shown in the state diagram of figure below: 7 1 5 3 Q2: If a 10-bit ring counter has the initial state as shown in figure below, determine the counter sequence. Note: Initially, a 1 is preset into the first and third flip-flops, and the rest of the flip-flops are cleared. PRE PRE 1 1 D D D CLR CLK Q: Find the sequence of the counter in the figure below. Begin with the counter cleared. D 10. K CLR K CLR of K CLR CK Note: Determine the logic expressions for the inputs Jo, Ko, Ji, K1, Jz and K2 firstly
Design a asynchronous sequential circuit with two inputs A and B and with one output Z. Whenever B is one, input A is transferred to Z. When B is zero, the output does not change for any change in A * 1 Add file