Being a Mechanical Engineer, you are asked to design/select a deep groove ball bearing of bore diameter of 2cm for an axial load of 1000 lbs and radial load of 500 lbs. Desired life is 200x106. Consider both load application factor and reliability factor 1.

Being a Mechanical Engineer, you are asked to design/select a deep groove ball bearing of bore diameter of 2cm for an axial load of 1000 lbs and radial load of 500 lbs. Desired life is 200x106. Consider both load application factor and reliability factor 1.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An 02-seris single-row deep-groove ball bearing with a 90 mm bore (C0 = 62 kN, C10 = 95.6 kN) is loaded with a 4.34 kN axial load and a 10 kN radial load. The inner ring rotates at 600 rpm (v=1). What is the FaC0? Should X1/Y1 or X2/Y2 be used to caculate the equivalent radial load? Determine the equivalent radial load experienced by this bearing. What is the bearing’s in-use reliability, assuming a design life of 2*10^8 revolutions and an application factor of 1.2?
An 02-seris single-row deep-groove ball bearing with a 90 mm bore (C0 = 62 kN, C10 = 95.6 kN) is loaded with a 4.34 kN axial load and a 10 kN radial load. The inner ring rotates at 600 rpm (v=1). What is the FaC0? Should X1/Y1 or X2/Y2 be used to caculate the equivalent radial load? Determine the equivalent radial load experienced by this bearing. What is the bearing’s in-use reliability, assuming a design life of 2*10^8 revolutions and an application factor of 1.2?
A device contains two bearings is to operate at 300 rev/min, 8 hours per day, 5 days per week for 5 years with a reliability of 0.99. The design load is 2024 N and an application factor of 1.2 is appropriate. Find the catalog rating C10 For ball bearings For roller bearings The Weibull parameters are and Use SI units. Take the relations as and Where the subscripts D: desired R: rating f: factor
Required information For a bolted assembly with six bolts, the stiffness of each bolt is kb 2 Mibf/in and the stiffness of the members is km = 13 Mlbf/in per bolt. An external load of 80 kips is applied to the entire joint. Assume the load is equally distributed to all the bolts. It has been determined to use 1/2 in-13 UNC grade 8 bolts with rolled threads. It is desired to find the range of torque that a mechanic could apply to initially preload the bolts without expecting failure once the joint is loaded. Assume a torque coefficient of K = 0.2. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the maximum bolt preload that can be applied without exceeding the proof strength of the bolts once the load is applied. The maximum bolt preload that can be applied is Ibf.
A winch drum of diameter 161 mm turning at 12pm lifts a load of 7.5kN. What is the winch output power?
b) Design a single row deep groove ball bearing with basic dynamic load rating of 33 KN to be used in a turbine to carry a radial load of 1584 N. The expected life of the bearing is 5591 hours at 529 rpm. Take k=3 for all types of ball bearings. Take the value of the shock load factor as 1.8. The radial and axial load factors are 1.3 and 1.6 respectively and the rotational factor is 1. Calculate: i) Expected life of bearings in millions of revolutions ii) Design equivalent dynamic load in N iii) Basic equivalent dynamic load in N iv) Axial load acting on the bearing in N
Calculate the basic rating life at 90% reliability for the following cylindrical roller bearing and conditions.Fr 5.05 kNFa 3.12 kNBearing: NU 1010 ECP (on pp 522 in the SKF catalogue)Clearance: Normal Give the answer in millions of revolutions.
A rigid coupling with 30 inches of bolt circle diameter transmits a torque of 18,000 lb-in. The coupling material has a yield strength of 90,000 psi. The coupling is fastened by six bolts. Assume design factor of N=3 Calculate the diameter of each bolt.
2) A shaft is designed with two 6305 bearings. At bearing 1, the radial load is 20 lb, and at Bearing 2, the radial load is 40 lb. What is the expected life of EACH bearing assuming a reliability of 97%? What is the reliability for BOTH bearings together?
RTI- PISUSSION ROLLING -ELEMENT BEARIN 6S ARE EITHER BALL BEARINGS OR ROLLER PEARINGS. PROPER INSTALLATION OF TMS bEMENTE WILL MINMIZE VIERATieN,