A beam with a solid homogeneous rectangular section is simply supported at A and B.A concentrated load F= 150 kilonewtons (kN) acts at point C where distance L1 (A to C) =2.50 metres (m) and distance L2 (C to B)= 1.65 metres (m). The dimensions of therectangular section of the beam are breadth, b = 35 mm and depthd = 125 mm.Calculate the second moment of area for rectangular section of the beam about itscentroidal x-axis (Ixxcentroid). Give your answer in mm4 and rounded to nearest mm4.9000

Given B = 35 mm D = 125 mm Moment of inertia of rectangle = bd3/12 Hence required solution is…

beam with a solid homogeneous rectangular section is simply supported at A and B. concentrated load F= 150 kilonewtons (kN) acts at point C where distance L1 (A to C) = .50 metres (m) and distance L2 (C to B)= 1.65 metres (m). The dimensions of the ectangular section of the beam are breadth, b= 35 mm and depth d = 125 mm. alculate the second moment of area for rectangular section of the beam about its entroidal x-axis (Ixxcentroid). Give your answer in mm4 and rounded to nearest mm4.

beam with a solid homogeneous rectangular section is simply supported at A and B. concentrated load F= 150 kilonewtons (kN) acts at point C where distance L1 (A to C) = .50 metres (m) and distance L2 (C to B)= 1.65 metres (m). The dimensions of the ectangular section of the beam are breadth, b= 35 mm and depth d = 125 mm. alculate the second moment of area for rectangular section of the beam about its entroidal x-axis (Ixxcentroid). Give your answer in mm4 and rounded to nearest mm4.

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 56P: Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0...

See similar textbooks

Similar questions

Alarge uniform cylindrical steel rod of density =7.8g/cm3 is 2.0 m long and has a diameter of 5.0 cm. the rod is fastened to a concrete floor with its long axis vertical.what is the normal stress in the rod at the cross-section located at (a)1.0 mfrom its lower end?(b)1.5 m from the lower end?
A wooden door 2.1 m high and 0.90 m wide is hung by two hinges 1.8 m apart. The lower hinge is 15 cm above the bottom of the door. The center of mass of the door is at its geometric center, and the weight of the door is 260 N, which is supported equally by both hinges. Find the horizontal force exerted by each hinge on the door.
ASAP
A long thin solid rod lies along the positive x-axis. One end is at x = 1.50 m and the other at x = 3.70 m. The linear mass density is A = ax3 + bx, where A is measured in kg/m, and the constants have the following values: a = 1.60 kg/m4 and b = 2.80 kg/m². Determine the total mass of the rod. Submit Answer Tries 0/10 Calculate the x-coordinate of the center of the mass for this rod. Submit Answer Tries 0/10
A beam with a solid homogeneous rectangular section is simply supported at A and B. A concentrated load F= 150 kilonewtons (kN) acts at point C where distance L1 (A to C) = %3D 2.50 metres (m) and distance L2 (C to B) = 1.65 metres (m). The dimensions of the rectangular section of the beam are breadth, b = 35 mm and depth d= 125 mm. Calculate the maximum bending moment that the beam experiences and give your answer in kilonewton metres (kNm) to two decimal places. *Assume the weight of the beam is negligible and zero. 2000
A post having a hollow, circular cross sectionsupports a P = 3.2 kN load acting at the end of an armthat is b =1.5 m long (see figure). The height of thepost is L = 9 m, and its section modulus is S = 2.653105 mm3. Assume that the outer radius of the post isr2 =123 mm, and the inner radius is r1 =117 mm.(a) Calculate the maximum tensile stress σmax andmaximum in-plane shear stress τmax at point A onthe outer surface of the post along the x axis dueto the load P. Load P acts at B along line BC.(b) If the maximum tensile stress and maximumin-plane shear stress at point A are limited to90 MPa and 38 MPa, respectively, what is thelargest permissible value of the load P?
A 2.0 – m uniform rod is 2.0 N. On one end is weight of 4 N (point A) while on the other is a load of 3 N (point B). A load of 1.0 N is suspended 0.5 m form point B and another 1.0 N load is suspended 0.75 m from the same point. If a 1.5 N load is suspended 0.25 m from point A, what is the amount of force needed to balance the rod? How far from point B shall the rod be balanced?
A uniform beam of length L possesses a mass of 50.99 kg. The beam is attached by a fixed support to a rigid wall, and is supported by a cable anchored to a second point on the wall, as shown here. The cable is attached to the beam at a distance of 40% of the total length L from the wall, and makes an angle of 35º from the vertical. The cable has a circular cross- section and a radius of 0.750 cm. a. Draw a free-body diagram. b. Write and develop all applicable state equations. c. Determine the amount of tensile force on the cable. d. Determine the magnitude and direction of the x and y components of the force at the fixed support e. Determine the magnitude and direction of the resultant force at the fixed support. f. Determine the stress on the cable.
A uniform stick can be balanced on a knife edge 10cm from one end when a load of 200N is hung from that end. When the knife edge is moved 5cm further from the end, the 200N load has to be moved to a point 8.75cm from the knife edge to obtain a balance. Find the length of the stick and its weight.
A 225 kg uniform, beam is hinged at one end and at the other is supported by a cable that is at 26 degrees to the left of the vertical. The beam is 2.8 m long and is at 8 degrees above the horizontalCalculate the tension in the cable (in N).
Find the x- and y-coordinates of the center of gravity of a 4.00 ft by 8.00 ft uniform sheet of plywood with the upper right quadrant removed as shown in the figure below. The dimensions of the cutout are a = 3.50 ft and b = 1.30 ft. ft %3D ft y(ft) x(ft)
The shaft shown in the figure is made of a material having 225 MPa. An axial load of 45 kN and torque of T are applied to the shaft. 45 kN Find the largest end torque T that can be applied for MSST. Take n=1.6, d=54 mm where n is the safety factor and d is the diameter of shaft.