please help Beam loading:-0.4 m-R₁800 N12 mmBeam cross-section:30 mm0.9 m0.8 mA400 N 600 N-+-0,3 m-+-0.3 m²B-0.3 m-0.4 m -C0.5 m-0.2 m/R₂200 NDetermine the Maximum Bending Moment and its location in the beam.

Answered: Image /qna-images/answer/0a867f5d-5e6c-4634-aa30-694ef7ca0b3d.jpg

Beam loading: 0.4 m R₁ 12 mm 800 N Beam cross-section: 30 mm 0.9 m 0.8 m A 400 N 600 N +0.3 -03 m-1-0.3 m- B -0.3 m---0.4 m- C |-0.5 m- -0.5 m-0.2 m- R₂ 200 N Determine the Maximum Bending Moment and its location in the beam.

Beam loading: 0.4 m R₁ 12 mm 800 N Beam cross-section: 30 mm 0.9 m 0.8 m A 400 N 600 N +0.3 -03 m-1-0.3 m- B -0.3 m---0.4 m- C |-0.5 m- -0.5 m-0.2 m- R₂ 200 N Determine the Maximum Bending Moment and its location in the beam.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Two rods and one cable are attached to the supports at O. If two of the forces are as shown,…

Q: A rocket runs out of fuel in the position shown and continues in unpowered flight above the…

Q: AW disk = 5 lb disk is travelling around in a circle of radius r₁ with an initial tangential…

A: The weight of the disk, Wdisk = 5 lbThe tangential velocity of the disk, vB1 = 5 ft/sThe velocity of…

Q: A cable that weighs 6 lb/ft is used to lift 500 lb of coal up a mine shaft 350 ft deep. Find the…

A: Mass of cable per unit length, m = 6 lb/ftMass of coal, Mc = 500 lbDepth, h = 350 ftRequired:W (…

Q: A viscous fluid of density 1200 kg/m3 and viscosity 0.9 Pa.s is confined in a spacing of 0,01 m…

Q: A ship has a radius of gyration of k=8m, a transverse metacentric height GM of 2m and a displacement…

A: The radius of gyration, kxx = 8 mThe metacentric height, GM = 2 mThe displacement force, F = 156960…

Q: Using the following lines, let us create a virtual data concerning the joint torque (Nm) and angular…

A: Given:To find:Torque average

Q: Determine the reactions at pin support A and roller support B when ß = 50°.

Q: A furnace is shaped like a 1-m-diameter and 1-m-long vertical cylinder. The base surface has an…

A: Given:Find:The net radiation heat transfer from side surface to top surface.

Q: Use the steam tables provided and use 4 decimal places for solving. A steam power plant operates…

A: Inlet turbine conditionsP[1] = 15000[kPa]T[1] = 500[C]Condenser pressure = P[3] = 5 kPaIt is asked…

Q: W B A Y Fj FM

Q: The rod has a diameter of 40 mm. It is subjected to the force system F₂1700 N, F, 600 N. F-900 N…

Q: Calculate -3 -6 . 10 ft L -3 ft a dx. a, ft/sec² 19 0 0 x, ft 5 7 10

A: Consider following acceleration vs displacement graph.We need to determine the total acceleration…

Q: QUESTION 26 A gate of a tank containing water and oil is kept in the closed position by applying a…

Q: Question: A capacitive displacement sensor, which works by measuring change in capacitance from the…

Q: Looking for correct answer asap !! Steam at 100 kPa and 200C is heated to 500C.What is the change in…

A: Given:The pressure is .The temperature is .The final temperature is .Formula used:The expression…

Q: A Scotch yoke is a mechanism that transforms the circular motion of a crank into the reciprocating…

Q: A fixed amount of water is enclosed in a cylinder and piston assembly. The mass of the water is 20…

A: Given- P1 = 2000 kPa…

Q: A model rocket is launched from point A with an initial velocity vo of 84 m/s. Also, the rocket's…

A: Let an object be launched from the point (0, 0) with the velocity at an angle from the horizontal.…

Q: Briefly explain the twin paradox, emphasizing what is paradoxical in the statement and how this…

A: The twin paradox theory is a special relativity thought experiment in which one of two identical…

Q: 60deg/s constant CCW angular velocity of the rider's thigh (upper leg), solve the mechanism…

A: where we drive these equation in terms of gthe veriable to obtain the velocity equationthe angular…

Q: A frictionless, freely moving piston-cylinder assembly with a mass of 85 kg and a cross-sectional…

Q: A w=6015 200 lb 12 in 60 18 in 6 in. B 35° 50 w = 7016 D с

A: Wright of the pulley, Wright of the beam, Diameter of the pulley, Value of point load,

Q: 2. The disk is originally rotating at w=8 rad/s. If it is subjected to a constant angular…

A: Initial angular speed of disk is 8 rad/s Angular acceleration is 6 rad/s^2 Required: Velocity,…

Q: Determine the direction delta of the resultant force acting on the corble measured couterclockwise…

A: F1 = 900 lbF2 = 600 lbF3 = 900 lb

Q: Replace the loading by an equivalent resultant force and couple moment acting at point O. (Figure 1)…

Q: A model rocket is launched from point A with an initial velocity vo of 84 m/s. Also, the rocket's…

Q: In raising the 51-m pole from the position shown, the tension T in the cable must supply a moment…

Q: The prototype water pump is required to generate a pressure rise of 750 kPa with the mass flux of…

A: For Prototype (Pressure rise)p = 750 kPa(Mass flux)p = 950 kg/sScale (Lr) = 1:5.5Water is used in…

Q: Water with a density of 998 kg/m³ (62.3 lb/ft³) enters a 50 mm (1.969-in.) pipe fitting…

A: Water density (ρ): 998 kg/m³Inlet diameter (Di): 50 mmInlet velocity (Vi): 1.0 m/sInlet gauge…

Q: A pressurized tank and piping system are shown in the figure. The tank pressure is maintained at 175…

A: P1 = 175 KPaLength L = 12mPipe of 1 std type M copper Z1 = 4 mZ2 = 1 m

Q: What is the fundamental difference between statics and dynamics in the field of mechanical…

A: In the field of mechanical engineering, the studies of statics and dynamics are used for…

Q: 12.19 Carbon dioxide discharges from a tank through a convergent nozzle with a diameter of 4 mm into…

A: Given the following: T0 =38oC pgage = 140 kPa pbar = 101.3 kPaFind the…

Q: Steam at 300 kPa and 200C undergoes an isentropic process where it expands until it becomes 30 kPa.…

A: SteamCondition 1P1=300 kPaT1 = 200 CCondition 2P2=30 kPaIsentropic expansion process

Q: A block of 50 kg is attached to a cable. The cable is then attached to a rotating assembly with a…

Q: 100 N 60⁰ c. 40 mm +P 40 mm --x 40 mm 1. the magnitude of the force P 2. the magnitude of the…

A: According to our guidelines , we are supposed to answer first three sub parts separately . Please…

Q: Iwo concentric springs are constructed with squared and ground ends from oil-hardened steel. The…

A: Given:The ultimate strength, Sut = 204,000 lbf/in^2The yield strength of steel, Syt = 0.75SutThe…

Q: find its equation of motion to find y (1). Round up the answer to the second decimal place point.

Q: 3. Draw a schematic of the standard convention for the meaning of positive shears and bending…

A: The intensity of load, w1 = 100 N/m at left end and 200 N/m at right endThe dimensions, d1 = 12 m,…

Q: The beam shown supports a load that varies uniformly from 100 N/m at the left end to 200 N/m at the…

A: Note-According to policy only first three questions can be answered so resubmit for complete…

Q: A machine with rational sections and subsystems is better than one that doesn't have either.

A: 1. Rational sections and subsystems in a machine are beneficial.EXPLANATION:Rational sections and…

Q: Design an analog Butterworth filter with the following properties. Find the transfer function?…

A: Step 1: Determine the filter order and cutoff frequency using the given specifications.From the…

Q: What are the factors that influence the buckling behavior of an axially loaded slender column in…

A: Buckling is a sudden, unstable deformation of a structure, often leading to its failure. It…

Q: Find the tensile force T1 in cable 1. (Write your result in N) Answer b) Find the tensile force T2…

Q: A fixed amount of carbon dioxide goes through a polytropic process where n=1.4. The initial…

Q: SolVe correctly please. There are 500 liquid medicines, 100 grams each, in a box. In how many…

A: Given:Number of liquid medicines = n = 500Weight of each liquid medicine = m = 100 g = 0.1 kgPower…

Q: Determine the reaction at A on the beam. Let wo = 97 kN/m, L= 3 m.

Q: For an ideal Rankine cycle, steam first enters the turbine at 5 MPa and 500C then it expands to a…

A: The turbine pressure is .The temperature at the turbine entry is .The condenser pressure is .

Q: two 20 x 100-mm and two 20 x 180 mm boards are glued together as shown to form a 120 x 200 mm box…

A: According to the given dataV=3.635kNWe need to findShear stress at glued point-B

Q: 6.* Figure 6 shows two plates of thickness t = 6 mm and width (into the paper) 50 mm tha are joined…

A: please refer handwritten solution

Concept explainers

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.

Question

please help

Beam loading:
-0.4 m-
R₁
800 N
12 mm
Beam cross-section:
30 mm
0.9 m
0.8 m
A
400 N 600 N
-+-0,3 m-+-0.3 m²
B
-0.3 m-0.4 m -
C
0.5 m-
0.2 m/
R₂
200 N
Determine the Maximum Bending Moment and its location in the beam.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Draw the given free-body diagram of the beam.

VIEW

Step 2: Apply moment and force equilibrium.

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute thew value of Ely at the right end of the beam loaded 3 m 400 N 400 N/m 1m 1m A Te R1=650 R2 =950 Eldy:/dx=M= 650x -400/2 X2 +400/2 (x-3)² +950 (X-4 ) =650x-200x²+200(x-3 )²+950 (x -4) Eldy/dx=650/2 x²-200/3x³- 200/3 (x-3 )³ +950/2 (x-4 )? +c1 EIY=325 /3 X3- 50/3 X' +50/3(X-3 )* +475/3(X-4 )³ +c1x +c2 Y=0, x=0 c2= 0 Y=0 ,X=4m
Draw the bending moment diagrams and shear force for beam and loading shown below 8 kip 700 lb/ft 15 kip-ft | 20 kip-ft 5 ft 5 ft 5 ft 5 ft
Refer to the beam shown below. Internal hinges are installed at points C and E. P = 47.25 kN P (KN) 20 kN/m A D E F +200 mt200 m-i -200 m-| 1 m|- 3.00 m- 2.00 m- - 2.00 m- 1 m a) Determine the support reactions. b) Calculate for the maximum positive and negative bending moment. c) Draw the shear and moment diagram (specify magnitudes at indicated points A, B, C, D, E, at maximum and minimum points, zero shear/s, zero moment/s etc.)
Current Attempt in Progress Plot the shear and moment diagrams for the beam loaded with both the distributed load and the couple. Then answer the questions. 410 N/m -2.2 m3.7 Questions: Atx=0.6m, V- Atx-3.7m, V- Atx-7.5m, V-I Atx-9.7m, V- 3.6 kN-m -2.2 m---2.2 m N.M N.M- N.M N.M- 1 The maximum (absolute value) shear force in the beam is The maximum (absolute value) bending moment in the beam is N-m N-m N-m N-m N N-m
Draw the shear diagrams for the beam shown below. (Label completely your diagram for full credit) 200 kN 120 kN 15 kN/m A E |B |C -6 m-8 m--10 m -8m
Draw complete shear and bending moment diagrams for the beam pictured below: 1000 lb 400 Ib/ft Mc 3 ft- -10 ft- FB 2 ft- FC
For the beam and loading shown, determine the bending moment value at point A If W = 3 KN/m, P=2 KN WkN/m PkN 30 OB 1.2 m 0.6 1.2 m 18 m 1.2 m m Select one: O A. -2.48 KN.m OB. -0.48 KN.m OC. -1.62 KN.m OD. 0.48 KN.m OE. 2.48 KN.m
12) Draw the SFD and BMD for the following. Locate the maximum bending moment and state it's value. 10kN 200kNm O klm *0-5m* 2m* 2kN/m 3m-
Draw the shear and bending moment curves for the beam and loading and the maximum absolute value of the shear and bending moment in the beam by the semi-graphical method. Explain how you come up with the solution/Answer. 30 kN 37 kN/m A D -1.8 m 0.9 m -3.6 m
Problem 4: Bending moment was determined to be 940 Ib-ft, at a beam's rectangular cross-section (width 3 in, height 9 in). What is the bending stress at point D on that cross-section, if it is located 7.5 in from its bottom edge? Hint: /- bh/12
1/4 You can explain the table of how to use or explain the words .of understanding a table TABLE 6-1. Cantllever Loadings CANTILEVER BEAM MOMENT EQUATION (moment at any section x) DEGREE OF МОMENT TYPE OF LOADING EQUATION MOMENT DIAGRAM AREA Zero b=L M=C*- Couple M = - C (i.e., M = - Cx°) bh 2 h=-C L b=L h=-PL Concentrated M = - Px Ist bh b=L w N/m wL? h=- 2 Uniformly distributed M = - 2nd - bh -L- w N/m b=L Uniformly varying wL? h=- M = - 3rd bh 6L -
Draw the shear and moment diagrams for the beam shown. After you have the diagrams, answer the questions. The distance x is measured from point A to the right. 265 Ib/ft 7.9' 3.7' Questions: At x = 3.9 m, V = ! Ib, M= Ib-ft At x = 9.8, V = i Ib, M = Ib-ft %3D The maximum absolute value of the shear force: |Vmax| = i Ib The maximum absolute value of the bending moment: |Mmax| Ib-ft %3D The bending moment is zero between the supports at x = i ft