Beam AB is subjected to a triangular load as shown below. Determine the Resultant and its distance from A.

Q: Compute the resultant 2. Compute the Angle of the Resultant with Respect to the x axis measured…

A:

Q: Determine the maximum moment of a 25-ft simply-supported beam  with a 1000 lb load at the center.

A:

Q: What would be the resultant moment of the three forces acting at the beam shown in the figure about…

A: Correct ans is d

Q: Draw the shear and moment diagrams for the beam.

A: The moment about point B is zero,Take moment about point B ,The Load w is acting same at each point…

Q: Determine the resultant couple moment acting on the beam shown: * 300 lb 200 lb 1.5 ft 200 lb 300 lb…

A:

Q: Find forces A and B in diagram at right.

A:

Q: Wo Determine the magnitude and location of the maximum bending moment M fastttt it's urgent

A:

Q: A beam is subjected to distributed loads as shown. Determine the magnitude and location of the…

A:

Q: 2. Find and illustrate the resultant of the distributed and concentrated loads acting on the beam.…

A:

Q: The magnitude of resultant force of the distribute loading shown is 5 kN/m 10 m

A:

Q: Determine the distance (in m) from Point O where the resultant acts

A: Consider the diagram as shown below for the given system.

Q: Forces act on the beam as shown. Determine the magnitude of F (Ib) so that the resultant moment Mis…

A:

Q: The assembly above is constructed out of a bent circular rod with a diameter of 1 in, Which of the…

A:

Q: Q.1) Find Qand the angle 0. If the force Ris the resultant P=3 kN of Pand Q. 55° R=2 kN

A: Given: P = 3 kN R= 2 kN   To find: Q= ? theta = ?

Q: Construct the influence line for the moment at point C of the beam. O

A:

Q: Determine the resultant and location of the line load acting on the beam using composite area…

A: Given Beam under force To find Resultant Location of load line

Q: A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area…

A: Given data: The second moment of area is I=11.5×106 mm4 The depth of rectangular cross section is…

Q: Calculate the resultant of the forces on the bracket shown. Reference the resultan respect to point…

A:

Q: If an axis of symmetry for the cross-section exists, the shearthe center lies at a point on this…

A: Given: Axis of symmetry for the cross section exists Whether the shear center lies at a point on the…

Q: 2. Determine the internal resultant loadings in a point 2 m from point A if the applied load is 10…

A:

Q: The truss carries forces shown in the figure. Determine the Resultant of the forces and its…

A: Rx=∑FxRx=(45+45)Cos45Rx=452 NRy=∑FyRy=-[(45+45)Sin45+15+15+15]Ry=-108.64 N  R=Rx2+Ry2R=125.91 N

Q: Q3) Determine the resultant of two forces by analysis them in rectangular component according to (x…

A:

Q: Replace the loading by a single resultant force, and specify its location on the beam measured from…

A:

Q: Beam AB is subjected to a triangular load as shown below. Determine the resultant and its distance…

A: Given data: Varying load intensity, Fi = 25 N/m. Length of the beam, L = 6 m. The resultant of a…

Q: 1. Determine the moment about the center of the bolt in the drawing below. (answer: 8.31 N-m CCW) 80…

A: Rotational effect of force about a point is called as moment. Moment = Force X Perpendicular…

Q: Specify where the resultant's line of action intersects the beam, measured from O

A:

Q: he bucket of the excavator at a construction site is subjected to Fi = 1530 lb and F= 790 lb digging…

A:

Q: Determine the magnitude of the equivalent resultant force of the distributed loading and specify its…

A:

Q: Draw Hu trianglef forces and the magnitude F2= 200N delermme and dinecthion f the resultant . 40° he…

A:

Q: Q6) Calculate the location the resultant (d) of the two forces acting on the beam about O. F=30 Ib…

A: The resultant force is the single force that is the sum of all the force that acted at a particular…

Q: Determine the Resultant Moment at A Determine the Resultant Moment at B  Determine the Resultant…

A: Given Force system To find Moment at A Moment at B Moment at C

Q: Find the moment for the force applied by a pair of 400 N forces on the wheel.

A: Given data  Magnitude of the couple force (F) = 400 N distance between forces (d) = 35 mm = 0.035 m…

Q: Determine the moments about point (A ) due to the forces applied on the cantilevered beam.

A: The moment about point A is 30.39 kN-m

Q: #8 Det. the resultant OF the Forces shown; 24 m. 28 in. 0216 106|b | I 45 in. 30 in 40 in

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.