B P2.3 and P2.4 2.4 Two structural members B and C are bolted to bracket A. Know- ing that both members are in tension and that P = 6 kips and Q = 4 kips, determine graphically the magnitude and direction of the resultant force exerted on the bracket using (a) the paral- lelogram law, (b) the triangle rule.

B P2.3 and P2.4 2.4 Two structural members B and C are bolted to bracket A. Know- ing that both members are in tension and that P = 6 kips and Q = 4 kips, determine graphically the magnitude and direction of the resultant force exerted on the bracket using (a) the paral- lelogram law, (b) the triangle rule.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter3: Resultants Of Force Systems

Section: Chapter Questions

Problem 3.17P: The 3200-1b weight is supported by two cables. Knowing that the resultant of the cable tensions T1...

See similar textbooks

Similar questions

Solve Prob. 2.4 by trigonometry.(Reference to Problem 2.4):Two structural members B and C are bolted to bracket A . Knowing that both members are in tension and that P = 6 kips and Q = 4 kips, determine graphically the magnitude and direction of the resultant force exerted on the bracket using (a) the parallelogram law, (b) the triangle rule.
360 mm 920 mm lo 600 mm 900 mm C.
1.Referring to the figure below, knowing that a = 20", determine the tension in (a) in cable AC. (b) in горе ВС. 1200 Ib 2. Referring to the block below, determine (a) the required value of a if the resultant of the three forces shown is to be parallel to the incline, (b) the corresponding magnitude of the resultant. 3. A transmission tower shown below, is heid by three guy wires anchored by bolts at 8, C, and D. (a) If the tension in wire AB is 525 Ib, determine the components of the force exerted by the wire on the bolt at 8. (b) A transmission tower is held by three guy wires anchored by bolts at 8, C, and D. If the tension in wire AD is 315 Ib, determine the components of the force exerted by the wire on the bolt at D. 100 t 20 25 20 60
2. A person's arm is used for ergonomic studies. If the distance of the AB, BC, and CD segments are 35.0 mm, 28.0 mm, and 19.0 mm, respectively, and the model is holding a small 1.5-lb load on the distal metacarpals of her hand . Determine the magnitude and direction of the moment of force with respect to a) to the shoulder joint, b) to the olecranon joint, c) to the carpal joint.
0.4 m B A 4.8 m 0.6 m 5.6 m E F 4.8 m x PROBLEM 3.51 A farmer uses cables and winch pullers B and E to plumb one side of a small barn. If it is known that the sum of the moments about the x axis of the forces exerted by the cables on the barn at Points A and D is equal to 7.6 kN-m, determine the magnitude of TDE when TAB = 1.02 kN. IDE = 1.14 KN
Q2) Two strings are passed around the four 1-in.-diameter pegs that are attached to a board and pulled with the forces shown. (a) find the magnitude and direction of the resultant couple acting on the board. (b) If only the string that passed around pigs B and C is used, what is the minimum value of the tension required to create the same couple as in (a). 25 lb 35 Ib 6 in. 35 lb 8 in. 25 lb
45 N Ans. (a) 34 N, 0=280 (b) dRA = 11.64 mm from B to the left; dRc3D62 mm below B 36 Dr. M.S. Meddah 3.116 A 160-N motor is mounted on the floor. Find the resultant of the weight and the forces exerted on the belt, and determine where the line of action of the resultant intersects the floor. 700 N 30° 50 mm -300 N 50 mm Final result: Resultant, R = 925.92 N and 0 = 11.840 x= -582.22 mm i.e. resultant intersects the floor 582.22 mm to the left of the vertical centerline through O. 37
A dirigible is tethered by a cable attached to its cabin at B. If the tension in the cable is 1040 N, replace the force exerted by the cable at B with an equivalent system formed by two parallel forces applied at A and C. A B 6.7 m '4 m 60° D
(6) 7. Given: The force system shown. Draw a F.B.D. of Point C and, Find the internal forces in members AC and BC. CABLE 3m STRUT 4m W= 285KN
1. To satisfy design limitations it is necessary to determine the effect of the 4.5 kN tension in the cable on the truss. For this purpose replace this force by its equivalent of two forces at A, F: parallel and Ea perpendicular to the truss. Determine F; and Fn. A 1250 4.5 kN 30°
An 8-m long cantilever beam is loaded with vertical forces A = 60 kN and B = 108 kN, separated by a distance d = 5.6 m, as shown. Replace the two forces with a single equivalent force R and determine the distance x-bar (x¯) from the left end of the beam to the line of action of R.
Q2) Two strings are passed around the four 1-in.-diameter pegs that are attached to a board and pulled with the forces shown. (a) find the magnitude and direction of the resultant couple acting on the board. (b) If only the string that passed around pigs B and C is used, what is the minimum value of the tension required to create the same couple as in (a). 25 lb 35 lb B 6 in. 35 lb 8 in. 25 lb