(b) Figure Q1 shows the front of a receiver consisting of a Low Noise Amplifier (LNA) connected to a radio frequency (RF) amplifier through a transmission line. If the output load is 30002, the system bandwidth is 200 kHz and the ambient temperature is 17°C Determine the Noise Factor (F), Noise Power (N.) and Noise Voltage (Vn) of the output if; (i) The amplifier is noise free and the transmission line is lossless. LNAS have gain of 10 dB, while RF amplifiers have gain of 12 dB. (5 marks) (ii) (iii) Noise figure (NF) for LNA and RF amplifier are 1 dB and 5 dB respectively. The LNA gain and RF amplifier are the same as in part (i). while the transmission line has a loss of 8 dB. Comment on the answers to parts (i) and (ii). Transmission RF V LNA Line Amplifier No

(b) Figure Q1 shows the front of a receiver consisting of a Low Noise Amplifier (LNA) connected to a radio frequency (RF) amplifier through a transmission line. If the output load is 30002, the system bandwidth is 200 kHz and the ambient temperature is 17°C Determine the Noise Factor (F), Noise Power (N.) and Noise Voltage (Vn) of the output if; (i) The amplifier is noise free and the transmission line is lossless. LNAS have gain of 10 dB, while RF amplifiers have gain of 12 dB. (5 marks) (ii) (iii) Noise figure (NF) for LNA and RF amplifier are 1 dB and 5 dB respectively. The LNA gain and RF amplifier are the same as in part (i). while the transmission line has a loss of 8 dB. Comment on the answers to parts (i) and (ii). Transmission RF V LNA Line Amplifier No

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Mark the good definition
Find the resonance point and the half-width of the speed versus frequency curve for the damped harmonic oscillator, under the action of a sinusoidal driving force. *It is all the data
4. Signal conditioning element basically takes the output of the sensing element and converts it into a form more suitable for further processing, usually in the form of a DC voltage, DC current or variable frequency AC voltage. The output of the sensing element is usually too small to operate an indicator or a recorder. Therefore, it is suitably processed and modified in the signal conditioning element so as to obtain the output in the desired form that is amplify the signal and filtering the unwanted signal. i. Describe the aliasing phenomenon. ii. Suggest a solution to minimize the effect of aliasing.
Provide solution
Which statement is true? a. In FSK, the modulating signal and the carrier signal are both analog b. In FSK, the modulating signal and the modulated signala re both digital c. In FSK, the modulating signal and the modulated signal are both analog d. In FSK, the carrier signal is analog and the modulating signal is digital
Identify the given statement. The fundamental benefit of direct PM is that the carrier oscillator is separate from the actual modulator circuit and can thus be a very steady source, such as a phase-locked loop. Select your answer. The statement is true. The statement is false. The statement is a case-to-case basis. The statement has no fixed information.
The conduction angle of class A amplifier is ?
A three-stage system comprised of two amplifiers and one filter. The input power Pin= 0.1mW. The absolute power gains are Ap1 = 100, Ap2 = 40, and Ap3 = 0.25 Determine a.) the input power in dBm, b.) output power (Pout) in watts and dBm, c.) the dB gain of each of the three stages, and d.) the overall gain in dB
I need the answer as soon as possible
A channel having a bandwidth of 1 kHz, the power of signal is 10 W and the power of noise is 5 W. Determine the channel capacity. Or: A channel having a bandwidth of 1 kHz and Signal to Noise Ratio (SNR) is 2. Determine the channel capacity.
(a) Construct MOD 12 asynchronous counter. What will be the output frequency, if the input frequency is 1 MHz. If the counter is at state 6, what will be the count after 60 pulses.
What Is frequency modulation and demodulation? Describe their importance and how they work.