b) A shaft whose nominal diameter is 30mm has limits of 30.013mm and 29.992mm. It is to make a transition fit with a bore. If the maximum interference between the mating components is to be 0.013mm and maximum clearance is to be 0.039mm. calculate: (i) The low limits of the hole (ii) The high limits of the hole (ii) The tolerance of the hole (iv) The high limits of the shaft (v) The tolerance of the shaft

b) A shaft whose nominal diameter is 30mm has limits of 30.013mm and 29.992mm. It is to make a transition fit with a bore. If the maximum interference between the mating components is to be 0.013mm and maximum clearance is to be 0.039mm. calculate: (i) The low limits of the hole (ii) The high limits of the hole (ii) The tolerance of the hole (iv) The high limits of the shaft (v) The tolerance of the shaft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider that fit between the shaft and the disk is of transition type where the maximum interference is required to be 0,013 mm. Nominal diameter of the shaft is 65 mm. The hole in the disk is machined to IT quality of 7. tolerence on the fit is 0.050 mm. Using the basic shaft system, determine the nearest fit from ISO tables.
The Fit of the two letter tolerances (P7& f7) When the basic size(160mm) * ?is Internal Fit. Transfer Fit Clearance Fit O * The Pitch diameter circle for the gear depends on Shaft diameter. Hub diameter Module and number of teeth the maximum internal fit of the two letter tolerances (G7& p6) When the * ?basic size (180 mm) is -56 -54 -53
The toleranced diameter of a hole is given as 0.990"/1.010" and the size of the mating pin is given as 0.985"/0.980 37. What is the maximum clearance for this fit? 0.030" 0.020" 0.025" c) 0.010" (P 38. What type of fit is this? transition b. clearance interference d. none of the above 39. A fit can be determined by specifying: upper limit b. allowance max. clearance b& c all the above TE d. 40. A fit is specified as 60H1109 in Metric unit. What is the tolerance grade for the shaft? 60 a. b. 9 11 d. none above
Complete the hole specification including a position tolerance of .018" diameter at MMC relative to primary datum feature A, secondary datum feature B, and tertiary datum feature C.
3. If the diameter with tolerance of the hole is 2.6 ±0.1 mm, which of the following is the safe diameter and tolerance of the shaft to ensure a clearance fit (no interference and not tight) when assembled? 2.6-0.05 mm 2.5-0.1 rum 2.6 ± 0.1 mm b. 2.5±0.1 mm a. C. d.
Matching hole and shaft, the size of the hole isp40+0.15 +0.05mm, the size of the shaft isq400. -0.1 Omm , and their gap is (). A. 0.25 B. 0.05 C. 0.15
Determine the limits of the corresponding shaft, for a Clearance Fit using the Basic Hole System, given the following information. Determine the minimum and maximum clearances. Show all work. The Basic hole size (minimum diameter) = 0.725" Tolerance of the parts = 0.005" Allowance = 0.004"
Machine shaft alignment theory and A. Theory of shaft alignment B. Evaluation of shaft alignment readings C. Equipments needed for shaft alignment D. Procedure of how shaft alignment is done. evaluation
In an interchangeable assembly, shafts of size -0.040 25.000-0.0100 mm mate with holes of size +0.020 25.000-0.000 mm. The maximum possible clearance in the assembly will be (a) 10 microns (b) 20 microns (c) 30 microns (d) 60microns
QUESTION 1 TOLERANCE A solid steel shaft with a diameter of 130 mm must be press-fittd in a journal bearing (Figure 1) with an inlet and outet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing hlet diameter as the basic size. Outlet Bearing Inlet Joumal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.
can you please find the solution question no:26
Is this a clearance or interference fit?