B: 82

Q: Dotermine all fur ce truss Shown mem bers of the

A:

Q: Find the controid for the shaded area 50 50 r=150 50 50

A:

Q: The value of shear stress in the principal plane is Resultant stress Maximum Zero O Minimum

A:

Q: Štrain is: Multiple Choice

A: Given data : Original length=LChange in length=∆LStrain has no Unit

Q: Determine ali fur ce of te mem bers truss Shown

A:

Q: HoW 3. Determine the weightin newtons of awomen whose weight in pounds is 130. Also, find her mass…

A: Weight in newton , kg and slug from 130 pound.

Q: Find (I,) for the shaded area.

A:

Q: Both ends of the fixed (fixed) rod were mounted at 0 °C. Calculate the minimum diameter of the bar…

A:

Q: From the figure below, choose the correct answer of the following 6 kN 5 kN 3kN 30° 0.2 m 4 В 2 m- 4…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: 20 Ibf 200 kg 250 20 kN m A 2 FT 200 kg

A: Find the resultant force at point C in N

Q: 1. Rectangle A = bh bh b. hb 12 hb ly = bh

A:

Q: A weight of kg is placed on the piston of a hydraulic lift with a diameter of 10 cm. The weight to…

A: data given; D1=10cm D2=? , F1=W=65kg , F2=1900kg applying pascal law F1A1=F2A2…

Q: 160 N 200 N 30- 100 nun 200 min 30 150 N A

A:

Q: Determine the value of its prope .P=50 kPa and u=3131.9 kJ/kg

A: Given: P = 50 kPa u = 3131.9 kJ/kg.   To find: Other properties at this state.

Q: 9 The British gold sovereign coin is an alloy ef gold and copper having a total mass of 7.988 g. and…

A:

Q: Figure Part A Determine the greatest load P that can be applied to the truss in (Figure 1) so that…

A: To find: The greatest load P applied to the truss. Given: The force exceeding either  2.6 kN in…

Q: (b) thickness of 15 mm as shown in Figure Q4. The pressure inside the tank is maintained at 10 MPa.…

A:

Q: A flat wall with conductivity A [W/(m K)] and thickness L [m], has a uniform heat generation g…

A: Given:  →T∞1=27°C →R1=0.004112 KW because length of the wall→L=0.15 m cross sectional area →Ac=0.64…

Q: Q5: For the below shaded area, calculate Ixand Kx 130 mm 30 mm 30 mm mmt- 40 mn -40

A:

Q: What are the Miller indices for the plane B drawn in the sketch below? +2 B A 1/3 12

A:

Q: 2 kN 2 kN 2 kN 2 KN 4 kN 4 kN -2 m- 1,25 m 1 m 1 m 1m 1m 0,75 m B

A: We can solve this by using the following steps:Draw the shear force and bending moment diagram. To…

Q: B) Determine the maximum force P that can be applied to block A without causing either block to…

A:

Q: Figure Q3 above shows the schematic of a motor on the right pulling the mass on the left. It is…

A:

Q: 400 N 3 m A, 8 m 4 m D 1200 N

A:

Q: Determine the centroid of the area shown below figure by the direct integration method.

A:

Q: Determine P and RA

A:

Q: Determine the work required for displacing a block by 50 m and a force of 5 kN. ans in kJ

A: Work done is given by the formulae, Work done = Force x Displacement Given data : Displacement = 50…

Q: The free body diagram of a rigid body shows O forces O moments support reactions All of these

A: Given data: -  The force F1 is F1 = 6 kN. The force F2 is F2 = 3 kN. The force F3 is F3 = 5 kN.

Q: Q3 Figure Q3 shows a flat belt connects a 1.20 m diameter pulley on a shaft running at 25 rad/s with…

A:

Q: BM at B is 3 kN 1 m D 1m 1 m B 1 m A

A:

Q: Determine the acceleration of the slider block C at this instant?

A: Given: To determine: Sliding velocity of Slider C

Q: Q3 Derive the relations 2²F' Cy = -T ƏT? and Cp 3 —Т ƏT² P

A:

Q: 6 ft y 9 + B E 4 ft- D H -4 ft 4 ft K +ft- G 3000 lb 1000 lb X

A: Given: Force applied at point H: →FH=3000 lb    (in downward direction) Force applied at point G:…

Q: Ţ Į 100 Mpa 75 Mpa 150 Mpa If the element shown was rotated 60° CW Find: (α)σχ' (b)ay' (c)tx'y

A: (a) To find: The value of principle stress σx'. Given :  The element is rotated by θ=60° counter…

Q: Determine the force in cored AB 30° A B 800 lb/ft -15 ft- -15 ft- Your answer

A:

Q: * Young's modulus is defined as the ratio of O Volumetric stress and volumetric strain O Shear…

A: The Young's modulus is defined as the ratio of Answer: Longitudinal stress and longitudinal strain

Q: Hiw. Detemminetthe Reseltant force dnd ites direction for the Systemso skown ini 50N 30 文4 7ON

A:

Q: Ex.6. Locate the centroid of the wire shown in Fig. 12 a. 20 mm 40 mm 12) (0) - 382 mm 20 mm Fig. 12…

A:

Q: A. 30 m 20 m B 50 m - 40 m

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.