Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 30 kips, F₂ = 14 kips, F3 = 20 kips, and F4 = 39 kips, determine the absolute value of the axial load in rod (2). To F₂ (1) F₂ F3 (2) (3) A O 24 kips O 18 kips O 21 kips 28 kips O 17 kips B F3 F4 C D

Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. If F₁ = 30 kips, F₂ = 14 kips, F3 = 20 kips, and F4 = 39 kips, determine the absolute value of the axial load in rod (2). To F₂ (1) F₂ F3 (2) (3) A O 24 kips O 18 kips O 21 kips 28 kips O 17 kips B F3 F4 C D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.21P: A slightly tapered bar AB of solid circular crass section and length L is supported at end B and...

See similar textbooks

Similar questions

A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
.17 A mountain-bike rider going uphill applies torque T = Fd(F = l5lb, d = 4 in.) to the end of the handlebars ABCD by pulling on the handlebar extenders DE. Consider the right half of the handlebar assembly only (assume the bars are fixed at the fork at A). Segments AB and CD are prismatic with lengths L, = 2 in.andL3 = 8.5 in, and with outer diameters and thicknesses d01 = 1.25 in. 101 = 0.125 in. and d03 = O.87in.,i03 = 0.ll5in, respectively as shown. Segment BC’ of length L, = 1.2 in. however. is tapered, and outer diameter and thickness vary linearly between dimensions at B and C. Consider torsion effects only. Assume G = 4000 ksi is constant. Derive an integral expression for the angle of twist of half of the handlebar tube when it is subjected to torque T = Fd acting at the end. Evaluate ‘b1-, for the given numerical1ues.
Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
Two separate cables AC and BC support a sign structure of weight W = 1575 lb attached to a building. The sign is also supported by a pin support at O and a lateral restraint in the '-direction at D. (a) Find the tension in each cable. Neglect the mass of the cables. (b) Find the average stress in each cable if the area of each cable is Ae= 0.471 in2.
.15 A hitch-mounted bicycle rack is designed to carry up to four 30-lb bikes mounted on and strapped to two arms Gil (sec bike loads in the figure part a) The rack is attached to the vehicle at A and is assumed to be like a cant silkier beam A BCDGII (figure part b) The light of fixed segment AB is U = 10 lb. centered 9 in. from A (see figure part b) and the rest of the rack highs W2 = 40 lb. centered 19 in. from A. Segment ABCDG is a steel tube o(2 X 2 in. with a thickness I = 118 in. Segment BCDGII pivots about a bolt at B with a diameter d1 = 0.25 in. to allow access to the rear of the vehicle without removing the hitch rack. When in use, the rack is secured in an upright posit ion by a pin C(diameter o( pin d, = 5116 in.) (see phoo and figure part C). The of returning effect of the bikes on the rack is resisted by a force couple F h at BC. (a) Find the support reactions at A for the fully loaded rack. (b) Find forces in the bolt at B and the pin at C. (c) Find average shear stresses in both the bolt at Band the pin at C. (d) Find average bearing stresses o, in the bolt at B and the pin at C.
Q2: A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 45 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 170 kN, determine the load carried by the steel rod. The modulus of elasticity for steel, Es = 200 GN/m², and brass, Es = 100 GN/m². A - 85000 N B - 90000 N C - 87000 N D - 93000 N
The rod made of two different materials is fixed at point A. AB aluminum, BC steel It is made of materials. E1 = 70 Gpa and E2 = 210 Gpa. P = 100 kN axial compressive force It affects the C point. The diameter of the circular bars is D1 = 80 mm, D2 = 40 mm and their length L1 = 20 cm. and L2 = 30 cm. (The direction of the force P is in the negative x-axis direction.) a) What are the displacements at B and C points? b) What is the reaction force at point A? c) What are the stresses in the bar?
Examine the rod below. It is fixed into a wall at the left hand end. From the wall to point B is 200mm. BC is 200mm long and CD is 200mm long. (Centreline to centreline distances). Point A lies on the positive Y-axis on a cross section halfway along BC. Three forces are applied at D. P=221.6, your individual load, is parallel to the z-axis. 400N is parallel to the y-axis and 200N is parallel to the x axis. The rod is a tube with an 80mm outer diameter and a wall thickness of 5mm. What is the net sigma (s) and the net tau (t) at Point A? Show all your working. Make sure you clearly indicate the direction/sign of each stress you calculate.
The rods 1, 2, and 3 shown below are welded together, mounted between two rigid walls and subjected to the two forces shown at joints B and C. Rods 1 and 3 are of the same length, L= L3 = 1.0 m and rod 2 has a length L2 = 1.8 m. Rods 1 and 3 are made from a material with E - 70 GPa. Rod 2 is made from a material with E = 100 GPa. The cross sections are given by: A1 = A3 = 11x10 mm? and A2 = displacements of joints B and C. %3D 17x103 mm?. Determine the %3D (2) 200 kN (1) (3) 350 kN A B DL
A round steel bar with a diameter of 1.500 in is subjected to the axial loads shown. P1 = 95 k, P2 = 115 k, P3= 55 k, P4 = (P1-P2+P3) k. If Section 2 has a length, L2 = 65 inches, find the change in length of Section 2. Report the answer below in inches, absolute value, 3 significant digits. P1 Your Answer: 100 inches Round Steel Bar P2 Section 2 12 P3 80 inches P4
A rectangular steel block is 76 mm long in the x direction, 50 mm long in the y direction, and 100 mmlong in the z direction. The block is subjected to a triaxial loading consisting of three axial forces asfollows: 214 kN tension in the x direction, 268 kN compression in the y direction, and 241 kN tensionin the z direction. If v = 0.30 and E = 200 GPa, determine the axial load in the x direction that wouldproduce the same deformation in the y direction as the original loading.
Q2: A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 45 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 170 kN, determine the load carried by the steel rod. The modulus of elasticity for steel, E, = 200 GN/m?, and brass, E= 100 GN/m. A - 85000 N B- 90000 N C- 87000 N D - 93000 N